For those buying these new "polished plates"......

[Drink My Dust]

Don't forget to plug them bolt holes for some extra mph. 8)

I had this stuff up on another site months ago.......but I think it still is good info for that extra .5-1.0 mph that is just too simple to resist........just puttting it up here for those that may have missed this the first time around......

...........here goes. I'm going to post the pics of the putty that we all got introduced to at Mud Bug #1.....this stuff was being used by none other than Tommy Jordan on his ski and with his permission I am passing on one of his tips that need not be forgotten.

The first two pics are the recommended putty to fill in the ride-plate holes and pump shoe holes.......

http://www.extremeteamracing.com/IMG_1090.JPG

http://www.extremeteamracing.com/IMG_1091.JPG

The second two pics are of holes that have had this in......but removed so you can see the layering process.

First take a strand of nylon rope and circle the bolt head.

Second take a patch of duct tape and stick to bolt head and rope (this will hold the rope in place and protect the bolt head from the putty adhering to it.

Third Apply putty to fill in the rest of the hole and sand smooth at end of process......stroke the sanding front to back of hull......not side to side.

Fourth......go out and GPS anywhere from .5-1.0 mph gains and wipe that smirk off your face. 8) Some have reported as much as 1.5 mph gains with this.......but I'd say .5-1.0 is average. When/if you need to remove the putty......simply tap with a screwdriver head a few time......out it all pops.

Here are the pics of the layers. The stuff is super easy to work with

Enjoy............. :D :D

http://www.extremeteamracing.com/IMG_1088.JPG

http://www.extremeteamracing.com/IMG_1089.JPG

Also keep in mind that you do not have to have a polished plate for this to work.......but please don't go to all that extra time/expense for these awsome plates...........and then leave some speed on the table cause you didn't do this. :wink:

[ABBOTT]

that stuff works good.

You can also use the 5 minute epoxy too with scotch tape in an "x" pattern (if your upsidedown) then just squeeze the goo in a side hole between layers of tape - then stick another piece of tape over the hole that you just used for the epoxy needle. The epoxy dries at the bottom of the hole just before the bolt hole (dries against the tape itself). Then it is sandable.

Either way is good. Good info. 8)

[ramnj]

I did this mod when you first posted and it does work. Instead of using that epoxy, i used a marine expoxy from Loew's. Can't remember the name but came in a blue package.

[RX951]

Dirt cheap at any Lowe's or Autoparts store. 3.99-4.99.
And as DMD stated, there are gains from this. :wink:



http://www.hydrotoys.com/gpr/tuners/rx951/hull%20repair/PICT2089.jpg

[GPRPITMAN]

Actually I have used the magnum and it blew out. So used a diffrent product called aqua mend at lowes

[RX951]

really? I have never lost a plug.....

[Knr]

i have yet to try this mod :oops:

[RX951]

i have yet to try this mod

dude ! you are leaving speed on the table :?

[Knr]

i think i will work on it this week :wink: ..my thing now is to find my 50-60 rpms im missing :evil: if i find it ill be one happy camper

[Fercho]

I have not sealed my plate holes yet

[Drink My Dust]

I have not sealed my plate holes yet

Good God ......What ARE we going to have to do with you Fernando. :wink: :lol: :lol:

[RichGPR]

I have to admit that I am unplugged (kind of like an acoustic set).
The speed left on the table does not bother me as much as knowing
that there are some holes that need plugging.
Kind of like Woody finding a new flock of sheep Baaaa Baaaaa

[WFO]

My pump shoe AND ride plate holes arent sealed :twisted: ...yet

[Green Hulk]

We see a 1 mph increase on the RXP's with this mod.

[Pistonwash]

I'm using jellybeans and bubble gum!! Works for the first 100 yards!! incredible holeshot!! :lol: :lol:


Sorry guys..I have had a long week..trying to be funny. :oops:

[WATER WOODY]

I have to admit that I am unplugged (kind of like an acoustic set).
The speed left on the table does not bother me as much as knowing
that there are some holes that need plugging.
Kind of like Woody finding a new flock of sheep Baaaa Baaaaa

EWE know it! :P :P :P :P

[ramnj]

This should be the last mod done after everything else is done.

[GPRPITMAN]

Yes just as Rafi said do this last after all your testing then plug away, Remeber when sanding the material back down make sure you get it even. The only material showing should just be in the holes (round) If it is not round sand more. I had left just a little bit outside of the holes and I am talking very little it made my boat slower and I was porposing

[jeff007]

so how do you get this epoxy out if you ever have to remove the bolts you covering up? do ya have to drill it out or what?

[N8R]

i used a dremmel with a carbide bit came out used needle nose to grab thin wire that i wrapped around bolts and the majority came out. bout 5 min a hole

[RonG]

Nate- so your signature is a blatent lie? You said you didn't fill your holes.
RULES COMMITTEE!!!!!!!!!!!!!!! :lol: :lol:

[N8R]

no i filled the pump shoe holes 2 times and re did the shoe 3 times when i ran the 79.3 i had no holes filled due to the fact that i might have to re due the shoe again.

[RonG]

OK- No rules committee necessary- ...BUT I'M WATCHIN YOU :lol: :lol:

[N8R]

you will be watching me pass you here in a couple weeks once Jim is done giving my ski some Florida love:smt113 :smt089

[RonG]

Already mounted the rearview mirror. Hope to see you soon.:roll: :roll:

[N8R]

i am going to try and make the FRS depending on health. did not go to hospital flying back to Florida tonight. if in to much pain there then i will go to emergency room. hoping ski will be ready by the end of the week and will be able to kick it this weekend with Jim , Forrest, Tragger etc

[elebouef]

you will be watching me pass you here in a couple weeks once Jim is done giving my ski some Florida love:smt113 :smt089
Hey are you running for some political office that you need the Bush support? First you get someone from Texas (Home of George Bush) and now you have someone in Florida(Home of Jeb Bush)

[RonG]

That's It!!!!!!! Im gonna move to Florida and play with all them guys too. I wont have you any faster than you already are. :( No one give Nate anymore parts or tricks.:evil:
Boycott Nate Boycott Nate
(Hope you feel better Bud):) :)

[N8R]

Hey are you running for some political office that you need the Bush support? First you get someone from Texas (Home of George Bush) and now you have someone in Florida(Home of Jeb Bush) i was thinking something like hatched in Texas raised in Florida. Ellie iam moving to Florida over the next 4-5 months and wanted it set up for Florida racing. most racers there are 1/8 and 1/4 mile . plus that is the nice thing about the Fercho package. lots of tech support and communication. of course i dont need to tell you something that you already know. all have to say is iam 200% satisfied by all the attention my ski has received. also the more pros who look at it the better it will become

[mtrager]

i am going to try and make the FRS depending on health. did not go to hospital flying back to Florida tonight. if in to much pain there then i will go to emergency room. hoping ski will be ready by the end of the week and will be able to kick it this weekend with Jim , Forrest, Tragger etc

Nate,

I hope you can make it I got a sweet ! For my bungalo.:D

[RonG]

Mark!!!!!
Mtrager wrote-...I got a sweet bunghole? :shock: :shock:

(Suite+ Bungalow) {spelling minus 2}8044

Forget it Mark.
There are some things even Nate won't do for speed secrets.
:lol: :lol:

(Guess I'm not movin to Florida);)

[mtrager]

You are sick Ron !:smt119 :smt100

[RonG]

Yeah- it was just too quiet around here. Thought I'd stir the pot. :)

If I could only use my powers for goodness instead of evil...:roll: :roll: ;)

[RonG]

Mark-How many of your guys are going to Amelia Island?

[mtrager]

Forrest, my wife and son. Stickem and Jose.

I have never been but from what i understand it is awesome.

The hotel is right on the water in the historic district.

I am probably going to leave the triple at home and bring an stx 15f along with my single.

[RonG]

Mine is in Tenn for for some R&R but if Kerry gets it ready in time, I'll see you folks down there. Sounds like fun.:)