Results 1 to 7 of 7
  1. #1
    digger
    Join Date
    Aug 2007
    Location
    London Ontario
    Posts
    28

    I need help and 1996 SLTX 1050 parts

    I need a help and parts
    I have 1996 sltx 1050,I have a bog from 2400 to 4000rpm,the engine and carbs are rebuilt,when i pull off the plug wire closest to the back there seems to be only a slight change in rpm,The engine will run on one plug on the other two cylnders.I seem to have good spark and i have fuel.I have decided to replace all the parts that i have not done so far.This is what i need .
    1.cdi box
    2.Ignition coil
    3.spark plug wire set
    4.reed valves
    5. float for fuel system
    6.pop of valve and gasket
    thank you...jim [email protected]


  2. #2
    casey67's Avatar
    Join Date
    Sep 2006
    Location
    Lemont,IL
    Posts
    2,571
    +1
    34
    What is your compression?

    If you have good spark on the pto cylinder, but question spark at higher rpm,you can measure the resistance of the plug boot-wire and coils to see if at all different.

  3. #3
    digger
    Join Date
    Aug 2007
    Location
    London Ontario
    Posts
    28
    comp is 158x3 it is all new how do i do that test thx

  4. #4
    casey67's Avatar
    Join Date
    Sep 2006
    Location
    Lemont,IL
    Posts
    2,571
    +1
    34
    The tests are all explained in the service manuals. They are on-line,in the tech section,full manual down loads.

  5. #5
    Buy American or Learn To Read This: >^$"#[email protected]*$:?</
    Join Date
    Jun 2009
    Location
    Glendale, Az
    Posts
    267
    If your going to replace the CDI box and ignition coil, you might as well buy the whole updated cdi, coil ,and stator update kit. There was one on Ebay yesterday for $250 shipping included and was brand new (cost $325+shipping normally)

  6. #6
    digger
    Join Date
    Aug 2007
    Location
    London Ontario
    Posts
    28
    i looked on ebay but could not find it

  7. #7
    Buy American or Learn To Read This: >^$"#[email protected]*$:?</
    Join Date
    Jun 2009
    Location
    Glendale, Az
    Posts
    267
    I misspoke, my friend reminded me it was here on green hulk performance forum, that someone had it forsale. i would put up a pthread for it under polaris classified. wish i could recall who had for you.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 1996 SLTX 1050 middle and front cylinder HOT HELP!
    By shogangp in forum Polaris PWC Performance
    Replies: 4
    Last Post: 05-01-2014, 09:27 PM
  2. coil needed for 1996 sltx 1050
    By davexc700 in forum Polaris Open Discussion
    Replies: 1
    Last Post: 08-17-2009, 05:45 PM
  3. Replies: 5
    Last Post: 07-20-2009, 09:10 AM
  4. I need help and 1996 SLTX 1050 parts
    By diggerbug777 in forum Polaris Open Discussion
    Replies: 0
    Last Post: 07-16-2009, 11:27 PM
  5. Hello I need help with 1996 Polaris 1050
    By Polaris rider 1 in forum Polaris Open Discussion
    Replies: 25
    Last Post: 09-21-2008, 12:32 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •