Results 1 to 4 of 4
  1. #1

    Join Date
    Jun 2009
    SW Pa

    Has anyone replaced a VX110 Ride Plate bolt retainers?

    Has anyone replaced the Ride Plate bolt retainers that are epoxied to the rear hull floor? I need to replace one that has damaged threads. If so how did you loosen the retainer without damaging the hull.

  2. #2
    Goliath's Avatar
    Join Date
    Jun 2008
    Morehead City, NC / Stow, OH
    In my GPR hull they were held by this green goop. All I had to do was use a heat gun until the goop changed color. Then took a chisel to the goop.

  3. #3
    KamikazeGPR's Avatar
    Join Date
    Mar 2007
    I just replaced a bracket on my 09 fzs last week.Broke a bolt in it. Wasn't bad at all.

    Took rear of ski apart, all the exhaust crap. used a heat gun to get the bracket warm, Put a bolt into bracket and tapped with a rubber mallet to pop one side free. Reheated bracket, reached in and grabbed the side that was loose and pulled easy and it popped free with glue intact.

    It did leave the sealant from inside the bracket on the hull. i used a screwdriver to lightly scrape away the sealant. it comes off in big pieces. It will leave some small stuff.

    I sprayed the small stuff with industrial goof off(any solvent will work) and scraped with screwdriver and wiped with rag.

    i lightly sanded the area with 60 grit paper. Lightly sanded the new bracket. Used 3m 5200 fast cure to fill hex's in the bracket and the space between them. Put new bracket in place. Be generous with the 5200. The excess will squeeze out.

    I let set up for 20 min, then bolted on ride plate. Let cure for 3 days and re-tightened plate to spec.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	0708091343.jpg 
Views:	47 
Size:	197.3 KB 
ID:	142629   Click image for larger version. 

Name:	0708091338a.jpg 
Views:	47 
Size:	210.0 KB 
ID:	142630   Click image for larger version. 

Name:	0721091710.jpg 
Views:	54 
Size:	138.3 KB 
ID:	142631  

  4. #4

    Join Date
    Jun 2009
    SW Pa
    Pictures and everything


    Thanks for the info

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Has anyone tried the Riva ride plate for the VXR/VXS?
    By Jarrett in forum Yamaha PWC Performance (4-stroke)
    Replies: 4
    Last Post: 07-07-2012, 05:49 PM
  2. Ocean Pro Ride Plate Bolt Pattern 1994 SL
    By rob2337 in forum Polaris Open Discussion
    Replies: 19
    Last Post: 12-10-2008, 11:43 AM
  3. ride plate bolts
    By Lnewland in forum Polaris Open Discussion
    Replies: 1
    Last Post: 07-11-2008, 05:23 PM
  4. Filled Ride Plate Bolt Holes.
    By mrchinup in forum 4-Tec Performance
    Replies: 36
    Last Post: 06-04-2006, 12:55 PM
  5. Amazed at impact of filling ride plate bolt holes.
    By mjammer in forum 4-Tec Performance
    Replies: 26
    Last Post: 05-12-2006, 05:53 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts