Page 1 of 4 1 2 3 ... LastLast
Results 1 to 10 of 32

Thread: rude 3

  1. #1
    BLACK MAGIC HEADERS hydrojunkie's Avatar
    Join Date
    Jun 2007
    Location
    new york
    Posts
    3,529
    +1
    3

    rude 3

    recently i purchased a rude 3 from mr. nils... i have 5 hours on it and i love it. i have been taking it easy ,but now i will unleash it.

    mods are as follows.....
    headers
    speedfreeks head
    08 cam
    rude 3
    les cooke 9100 ecu
    60 mm thot body
    les cooke intake mani
    4 inch rear air
    x intercooler, "not xs"
    72 lb injecters
    rrfpr set at 50 psi
    h o walbro pump


    at idle my ski is seeng 13.2
    at wot my ski is seeing 12.4

    rpm's at 8600 with 85 % humidity @ 81 deg f

    my boost gauge craped out so i installed my aem true boost.

    at 0 hours charger slip was 190 inch lbs
    at 2 hours charger slip was 165 inch lbs
    at 5 hours slip was 150 inch lbs

    just pulled the charger for an inspection and reajust the slip.reset to 190 inch lbs.
    installed new gauge will post results.


    as for speeds i an using a 14 vein setback lescooke pump, with a 14/18 3 blade that dean charrier uses in his sons race boat.my pump tunnel is open to 162 mm,so my speeds will be off about 4 to 5 mph.
    right now with no boost gauge ski gps with a full tank on the seat 79.9.. @8500 rpm..

    now that the charger is good as new and boost gauge is installed i will post results tommorow. cool..................


  2. #2
    ADSR's Avatar
    Join Date
    Jul 2008
    Location
    Canadian West Coast
    Posts
    669
    +1
    2
    Very nice! Take some vids if you can!

  3. #3
    West Texas RXP skoepp's Avatar
    Join Date
    Oct 2007
    Location
    west texas
    Posts
    12,019
    +1
    149
    nice Jason!!!

    can't wait to hear more as you get it dialed in.....

  4. #4
    Ride Hard! aha's Avatar
    Join Date
    Jul 2005
    Location
    Covina, Ca
    Posts
    2,009
    +1
    11
    How is the acceleration? Spinning the prop from a dead stop?

  5. #5
    BLACK MAGIC HEADERS hydrojunkie's Avatar
    Join Date
    Jun 2007
    Location
    new york
    Posts
    3,529
    +1
    3
    Quote Originally Posted by aha View Post
    How is the acceleration? Spinning the prop from a dead stop?
    the prop i am using is from a professional race boat,basicly it will rip your arms off.if your not holding on you will go flying off the ski.

    HOWS THAT FOR AN ANSWER

  6. #6
    eric1238's Avatar
    Join Date
    Jun 2005
    Location
    Smith Mtn. Lake VA
    Posts
    728
    +1
    2

    79?

    4 to 5 mph? I have seen skis with a 9.5ish lbs high boost wheels go 79+. I am sure not near the hole shot you have but with your header etc., I would think ALOT more woud be there with Rude 3?

  7. #7
    BLACK MAGIC HEADERS hydrojunkie's Avatar
    Join Date
    Jun 2007
    Location
    new york
    Posts
    3,529
    +1
    3
    Quote Originally Posted by eric1238 View Post
    4 to 5 mph? I have seen skis with a 9.5ish lbs high boost wheels go 79+. I am sure not near the hole shot you have but with your header etc., i would think alot more woud be there with rude 3?
    dude you have no idea what your talking about.
    Start all over and read again. And dont make a dumb ass comment like that either.

    Oh and ps install spell check.

  8. #8
    Mik72e's Avatar
    Join Date
    Jan 2006
    Location
    Australia (Sydney)
    Posts
    1,472
    +1
    3
    Jay whens it for sale mmmm might be interested in a new ski u never know.

    Don t get caught up in comments everyone know everything remember.

  9. #9
    Ride Hard! aha's Avatar
    Join Date
    Jul 2005
    Location
    Covina, Ca
    Posts
    2,009
    +1
    11
    Quote Originally Posted by hydrojunkie View Post
    the prop i am using is from a professional race boat,basicly it will rip your arms off.if your not holding on you will go flying off the ski.

    HOWS THAT FOR AN ANSWER
    That is EXACTLY the answer I have been looking for! Thanks so much Jason!

  10. #10
    R88ory RXP's Avatar
    Join Date
    Feb 2008
    Location
    Kent, England
    Posts
    2,737
    +1
    46
    Quote Originally Posted by eric1238 View Post
    4 to 5 mph? I have seen skis with a 9.5ish lbs high boost wheels go 79+. I am sure not near the hole shot you have but with your header etc., I would think ALOT more woud be there with Rude 3?
    Basicaly the way Hydro has this boat setup is like a CC boat. Its not about topspeed coz your never gona see it its all about accell. 1 guy that races over here in UK has a GP boat with full turbo/autronics the lot and it will only do 85 flat out. But f*ck me does it get there fast. Its like watching an elastic band being shot. R88
    Last edited by R88ory RXP; 08-01-2009 at 03:05 AM. Reason: SP

Page 1 of 4 1 2 3 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Thursday 11/30 Rudee Inlet/GB LOX
    By pullthemover in forum Southeast
    Replies: 1
    Last Post: 11-30-2006, 10:23 PM
  2. for those of you who have rude fuel controler?
    By beachboy66 in forum 4-Tec Performance
    Replies: 9
    Last Post: 09-05-2006, 10:53 AM
  3. got my new Rude Performance controler in!
    By beachboy66 in forum 4-Tec Performance
    Replies: 6
    Last Post: 08-16-2006, 09:15 PM
  4. IC + Bkit + new RRECU + Rude fuel controller + injectors...
    By theantiRXP in forum 4-Tec Performance
    Replies: 9
    Last Post: 04-20-2006, 03:13 AM
  5. Rude Performance
    By meeper in forum 4-Tec Performance
    Replies: 5
    Last Post: 04-13-2006, 09:42 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •