Results 1 to 7 of 7
  1. #1

    Join Date
    Jun 2009
    Location
    EAST COAST
    Posts
    41

    Talking Engine lifting ring/plate

    anyone know where to find cheap pwc engine lift ring or plate to extract motors with engine hoist.thanks


  2. #2
    Quote Originally Posted by TMPLUMBER59 View Post
    anyone know where to find cheap pwc engine lift ring or plate to extract motors with engine hoist.thanks
    if your talking about a 4tec engine.....? mine came with it stock one in the front and one in the rear

  3. #3

    Join Date
    Jul 2009
    Location
    Stonington, CT
    Posts
    151
    The 4tec have lifting eye's...
    - but once you take the head off - they go with it.

    So I just grabbed some 1" tubular webbing (purchase at EMS Sports). Took 2 - 8' sections and tie them into a loop. Feed one end under the motor, (one front, one back) then clip the four ends together on the hoist. You end up with a quick sling setup for under $25. Webbing is rated for 2000lbs+ so it's not going anywhere and it doesn't scratch anything.

  4. #4
    West Texas RXP skoepp's Avatar
    Join Date
    Oct 2007
    Location
    west texas
    Posts
    12,019
    +1
    149
    If you have the head off use 2 of the stock head bolts with a chain or if you have everything off engine you can lift out of hull by hand but be careful on the back.

  5. #5

    Join Date
    Jun 2009
    Location
    EAST COAST
    Posts
    41

    Sea 2 the doo

    its on an 800cc.i have a chain hoist set up n my garage for pulling the motors.they make rings that go into spark plug hole but there $30 just lookin 4 safe cheap way i need all my toes.LOL

  6. #6
    mrbtd's Avatar
    Join Date
    Jul 2005
    Location
    Lindenhurst, Illinois, United States
    Posts
    4,309
    +1
    2
    Good lord..reach in there and pick it up.

  7. #7
    Dr Len's Avatar
    Join Date
    Jan 2006
    Location
    New Jersey Attitude Capital of the World
    Posts
    1,170
    Made 2 with old spark plugs and some big washers Well Rab 1 made them for me. He had the mig welder

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. SOLD Later year, SS engine lifting hooks
    By rangermtb5 in forum Sea Doo Classifieds
    Replies: 10
    Last Post: 10-11-2013, 07:08 AM
  2. yamaha gpr 66v engine?"PISTON RINGS"
    By thomaswester in forum Yamaha PWC Performance (2-stroke)
    Replies: 2
    Last Post: 07-15-2010, 09:29 AM
  3. Engine lifting ring/plate
    By TMPLUMBER59 in forum 2-Stroke Performance
    Replies: 3
    Last Post: 08-06-2009, 09:42 PM
  4. Engine lifting ring/plate
    By TMPLUMBER59 in forum Yamaha PWC Performance (2-stroke)
    Replies: 16
    Last Post: 08-05-2009, 06:46 PM
  5. Engine lifting ring/plate
    By TMPLUMBER59 in forum Yamaha PWC Performance (4-stroke)
    Replies: 0
    Last Post: 08-05-2009, 01:14 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •