Results 1 to 3 of 3
  1. #1

    engine mounts (? for ya jerry)

    noticed a conversation about the front engine mount in another post......anyhow.......this front engine mount..how much is it and how do you replace old one? i saw you said to have someone hoist the front of the engine up then slide in new one....is there shims??? wont pulling up engine in front do damage to others in back that are still tight????? whats the new one look like? i ride nasty chop and still no problems ....60 hours on 05.....
    Also need a new wear ring and perhaps prop...im stock except intake grate.....(any recommendations? gratis...)


  2. #2
    Site Admin Green Hulk's Avatar
    Join Date
    Apr 2005
    Location
    Morgan City, LA
    Posts
    36,398
    +1
    2,524
    Quote Originally Posted by 2005cdoorxp View Post
    noticed a conversation about the front engine mount in another post......anyhow.......this front engine mount..how much is it
    Here you go!
    http://www.4-tecperformance.com/inde...roducts_id=501

    Quote Originally Posted by 2005cdoorxp View Post
    and how do you replace old one? i saw you said to have someone hoist the front of the engine up then slide in new one....is there shims???
    Very easy, unbolt the front, lift engine, slide new mount in place, bolt it down. There will be shims under the stock mount. Leave these in place when you install the new mount.

    Quote Originally Posted by 2005cdoorxp View Post
    wont pulling up engine in front do damage to others in back that are still tight?????
    No because they are rubber and are flimsy. They flex very easily and are forgiving enough for you to lift the front of the engine up.

    Quote Originally Posted by 2005cdoorxp View Post
    Also need a new wear ring and perhaps prop...im stock except intake grate.....(any recommendations? gratis...)
    For a stock RXP you want to go with this impeller
    http://www.4-tecperformance.com/inde...&products_id=8

    Your wear ring choices are the stock plastic
    http://www.4-tecperformance.com/inde...roducts_id=518

    Or after market stainless
    http://www.4-tecperformance.com/inde...roducts_id=401

    Since you ride in rough water the R&D grate is going to give you better hookup
    http://www.4-tecperformance.com/inde...roducts_id=580

    If top speed is what you are after then the Riva grate is a better choice
    http://www.4-tecperformance.com/inde...&products_id=5

  3. #3
    thanks man! greatly appreciated.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. FS - Parts Engine mount/bed plates for red domestic engine
    By K447 in forum Polaris Classifieds
    Replies: 2
    Last Post: 11-14-2013, 10:11 AM
  2. FS Billet Engine Mount for SEADOO RXP/RXT/RXP-X/RXT-X
    By SingTH in forum Sea Doo Classifieds
    Replies: 1
    Last Post: 02-18-2013, 11:41 PM
  3. WTB Need engine mounts for a 99 slth
    By Mr. Matrix in forum Polaris Classifieds
    Replies: 5
    Last Post: 12-29-2010, 02:01 PM
  4. WTB Rear engine mounts for rxp
    By Insanediego Joe in forum Conversion Skis Classifieds
    Replies: 6
    Last Post: 05-08-2010, 06:09 PM
  5. Need an Engine Mount for my GP1200!
    By bullisland in forum Yamaha Old School Skis
    Replies: 7
    Last Post: 04-07-2010, 01:17 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •