Page 1 of 2 1 2 LastLast
Results 1 to 10 of 14
  1. #1

    Need a 1050 jug - 3021009

    I need a stock bore 301009 jug for a little project I picked up last week. Could probably use a dome too.

    Let me know what ya got!


  2. #2
    ph2ocraft's Avatar
    Join Date
    Apr 2006
    Location
    Campbell, Ca.
    Posts
    14,100
    +1
    105
    You want the actual hard to find 009 cylinder or the replacement??

  3. #3
    Quote Originally Posted by ph2ocraft View Post
    You want the actual hard to find 009 cylinder or the replacement??

    Are 3021018 ones the replacements?


    I picked up a '96 sltx with a bad MAG piston last week. It had the 009s on it.

    I also melted PTO on the 900 last week (and started to burn the MAG too). So I've decided I might as well convert it to a 1050 while I'm at it.


    I already had 2 bore-able 009s and one that has a questionable gouge around the outer o-ring on the head. I have a set of good 1.0 oversized pistons to go with these. I figure I could use these two good ones plus the slightly burnt one from the new 1050 since they all need to be bored out any way.

    That leaves me needing one good stock 1050 to match up to the remaining 009s that are already on the SLTX.



    (My other hope is that the MAG jug from the 1050 can just be honed and still be in spec. Gonna drop them all off at the machien shop this week and see what they say. If this works, I may also be able to get them to repair the other dinged one and have a full set for the oversize bore.)

    But it'd be easier to just find a good replacement!

    So....ummm.....are the 009s and 1018s the same or is there a difference in the ports or anything?

  4. #4
    ph2ocraft's Avatar
    Join Date
    Apr 2006
    Location
    Campbell, Ca.
    Posts
    14,100
    +1
    105
    You should stay with the 009 so you're matched. Wether you would actually know or feel the difference I don't remember. Remind me and I'll see if I have a good used 009 or just some new ones.

  5. #5
    john zigler's Avatar
    Join Date
    Aug 2006
    Location
    WI
    Posts
    2,545
    +1
    33
    i have two, std bore, freshwater 1019's here honed, and ready to bolt on, 100.00 ea + s&h

    send me an email, or call the shop, if that helps you at all.

  6. #6
    Quote Originally Posted by ph2ocraft View Post
    You should stay with the 009 so you're matched. Wether you would actually know or feel the difference I don't remember. Remind me and I'll see if I have a good used 009 or just some new ones.
    Thanks. If I can't find a good 009 I may be giving you a call. I actually need some other small random parts so I'll be calling any way...pretty sure you had them listed on your site.


    Quote Originally Posted by ph2ocraft View Post
    You should stay with the 009 so you're matched. Wether you would actually know or feel the difference I don't remember. Remind me and I'll see if I have a good used 009 or just some new ones.
    You're reminded!

    Lemme know what you find when you get a chance to look.

  7. #7
    Bump. Still looking for a good stock 009!!

  8. #8
    ph2ocraft's Avatar
    Join Date
    Apr 2006
    Location
    Campbell, Ca.
    Posts
    14,100
    +1
    105
    I'm unable to locate my 009's yet I know I have 8. I'm going to the shed tomorrow and have a look.

  9. #9
    Sweet...let me know!

    I watched at least 3 of these sell on ebay in the past 3 or 4 weeks.....but I didn't own a 1050 back then!

  10. #10
    BUMP!

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. WTB - Parts Need decent 780 jug and piston
    By nick072010 in forum Polaris Classifieds
    Replies: 3
    Last Post: 03-28-2012, 02:48 PM
  2. Need crank and jug
    By 88workcar in forum Yamaha PWC Performance (2-stroke)
    Replies: 2
    Last Post: 03-05-2012, 04:41 PM
  3. 700 and 1050 Jug Part Numbers - What's the difference?
    By bgaidan in forum Polaris Open Discussion
    Replies: 2
    Last Post: 08-27-2009, 06:17 PM
  4. Need help 1050 Overheats
    By Polaris rider 1 in forum Polaris Open Discussion
    Replies: 3
    Last Post: 09-15-2008, 10:16 PM
  5. need 900-1050 coils and cdi
    By keith neff in forum Polaris Classifieds
    Replies: 0
    Last Post: 07-11-2008, 04:57 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •