Results 1 to 7 of 7
  1. #1

    Join Date
    May 2006
    Location
    Smith Lake
    Posts
    286
    +1
    2

    Need Help...OIL BEEP, Limp mode

    Guys i have a stage 3 plus 05 rxp, open loop cooling and riva plate. Heres where i have problems, after a wot run it beeps and displays OIL, then kinda goes into limp mode for a second. If u pull key out it starts and runs fine...Plenty of oil, afr's are 12's in mid and 11.5.- 11.9 wot.....Any suggestions why she goes into this limp mode?


  2. #2
    Nothin' better than Doo'in it! BigDaddyRXP's Avatar
    Join Date
    Aug 2007
    Location
    Tampa Bay, FL
    Posts
    9,202
    +1
    673
    Oil pressure sensor

  3. #3
    speedskixp's Avatar
    Join Date
    Feb 2008
    Location
    venice fl.
    Posts
    8,117
    +1
    120
    Quote Originally Posted by bigdaddyRXP View Post
    Oil pressure sensor
    +1.

  4. #4
    2006 Turbo RXP boBO's Avatar
    Join Date
    Mar 2008
    Location
    STATE OF KUWAIT
    Posts
    1,034
    Also might be Oil filter
    Quote Originally Posted by bigdaddyRXP View Post
    Oil pressure sensor

  5. #5

    Join Date
    Feb 2006
    Location
    Birmingham AL
    Posts
    2,924
    +1
    2
    It is a new oil filter he also has a new (used motor ) in the ski it did it before the used motor went in and now it is doing it after the motor is in. It is a motor complete swap onlythings that were transfered from the old motor is the intake with all electronics on the intake.

    I was thinking that when he beats on the motor the oil is getting gassed up and thined out is it possible that the thin oil gets hot it is having low oil PSI? I told him to change the oil and see if it stops for a little while. I am also going to put a valve on his motor to get some heat in it due to the open loop cooling his motor is running Ice cold.

  6. #6
    Nothin' better than Doo'in it! BigDaddyRXP's Avatar
    Join Date
    Aug 2007
    Location
    Tampa Bay, FL
    Posts
    9,202
    +1
    673
    Quote Originally Posted by Lvnspeed View Post
    It is a new oil filter he also has a new (used motor ) in the ski it did it before the used motor went in and now it is doing it after the motor is in. It is a motor complete swap onlythings that were transfered from the old motor is the intake with all electronics on the intake.

    I was thinking that when he beats on the motor the oil is getting gassed up and thined out is it possible that the thin oil gets hot it is having low oil PSI? I told him to change the oil and see if it stops for a little while. I am also going to put a valve on his motor to get some heat in it due to the open loop cooling his motor is running Ice cold.
    That's not good... as the oil is probably mostly fuel I don't understand why so many people are jumping on the open loop band wagon... the sacrifices are not worth the benefits IMO. A remote heat exchanger is the way to go... if you want to run a open loop plate!

  7. #7
    KC Blue Thunder's Avatar
    Join Date
    Oct 2007
    Location
    Jacksonville, Florida
    Posts
    2,079
    Quote Originally Posted by bigdaddyRXP View Post
    That's not good... as the oil is probably mostly fuel I don't understand why so many people are jumping on the open loop band wagon... the sacrifices are not worth the benefits IMO. A remote heat exchanger is the way to go... if you want to run a open loop plate!
    +1

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. oil warning limp mode 07 rxt help
    By mrgoodwrench_420 in forum 4-Tec Performance
    Replies: 1
    Last Post: 07-01-2015, 09:17 PM
  2. Oil Ligt & Limp Mode
    By 05Limited in forum 4-Tec Performance
    Replies: 3
    Last Post: 08-21-2012, 12:43 PM
  3. RXP oil issue limp mode.
    By Chowner in forum 4-Tec Performance
    Replies: 7
    Last Post: 06-29-2012, 08:00 PM
  4. Newby needs help - oil and metal shavings in bilge of 97 WV760
    By 93AmSkier in forum Yamaha Old School Skis
    Replies: 12
    Last Post: 08-22-2008, 10:37 AM
  5. Newby needs help - oil and metal shavings in bilge of 97 WV760
    By 93AmSkier in forum Yamaha Open Discussion
    Replies: 0
    Last Post: 08-14-2008, 12:27 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •