Results 1 to 7 of 7

Thread: Problems??

  1. #1
    big83bronco's Avatar
    Join Date
    May 2006
    Location
    Macon, GA
    Posts
    326

    Problems??

    OK i put my ski back together adn the damn thing will turn over for about 5 seconds then stop itself. It will never fire up though. THen the warnign light stays on and you cant try to start if for about 15-20 seconds then the same thing again. I put an old plug in one of the wires adn none of the wires have a spark.

    So then I put in a borrowed advent and it started right up.

    I know it has somethign to do with my factory electrical box, but what is it? BTW I did install a Pro-Tec CDI a month ago, but the ski ran fine when i disassembled the exhaust and carbs last weekend. Now it does this stupid no starting thing.

    What gives?


  2. #2
    Mr Bill's Avatar
    Join Date
    Aug 2005
    Location
    Macon Georgia
    Posts
    451
    Your ski is haunted.

  3. #3
    txgp1300r's Avatar
    Join Date
    Apr 2006
    Location
    Dallas , Texas
    Posts
    3,382
    +1
    165
    did you check the temp sensor ? or is the wire damaged...mine did the same thing and it was the damm temp sensor.

  4. #4
    big83bronco's Avatar
    Join Date
    May 2006
    Location
    Macon, GA
    Posts
    326
    temp sensor wasnt plugged in. On either the stock or the advent, my pipe doesnt have one. Am I correct in assuming the advent is made to run the motor with it disconnected and the stock one has to have it connected to get spark to the spark plugs.

    I ran a jumper wire on teh temp sensor harness and it didint change the outcome on the stock box.?????????

  5. #5
    YudLuz2's Avatar
    Join Date
    Jun 2005
    Location
    Flowood MS
    Posts
    1,648
    +1
    111
    You need to have the temp sensor pluged up on the stock or pro-tec CDI, you don't have to mount it in your pipe, just have it plugged up. The advent or the r&d ignition lets you turn that function off so you dont need
    one at all.

  6. #6
    Mr Bill's Avatar
    Join Date
    Aug 2005
    Location
    Macon Georgia
    Posts
    451
    Sounds like you found the problem!

  7. #7
    2000 GPRXP 4tec shooter98xpl's Avatar
    Join Date
    Dec 2005
    Location
    Charleston SC
    Posts
    2,717
    +1
    3
    hahahaha, see told you Tim. You probably didn't plug it up right the first time when we told ya. So plug it up. I will pull your temp sensor off your other pipe, but man, that thing looks beat up pretty bad.
    I'll bring it sunday with me.
    SHOOTER

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Troubleshooting the Rotax Racing Stage I kit (was problems)
    By Jarrett in forum 4-Tec Performance
    Replies: 104
    Last Post: 10-22-2005, 08:12 PM
  2. riva stage 1 kit problems
    By macattack in forum 4-Tec Performance
    Replies: 3
    Last Post: 06-28-2005, 05:08 PM
  3. Found my Problem with My RXP after Service.
    By Water4fire in forum 4-Tec Performance
    Replies: 5
    Last Post: 06-20-2005, 03:12 PM
  4. Mysterious problem on my RXP
    By Jeff C in forum 4-Tec Performance
    Replies: 8
    Last Post: 06-13-2005, 10:08 AM
  5. 04 RXP Starting problem/question...
    By BLOWNRXP in forum Sea Doo Open Discussion
    Replies: 10
    Last Post: 06-01-2005, 10:14 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •