Results 1 to 9 of 9
  1. #1

    No Power Or Anything!!!

    Ok guys so I left my ski for a week over Thanksgiving and it ran perfect...When I came home I went to crank it up and I have absolutly no power to anything! Guages, Motor, Nothing...So i replaced the Battery and still nothing! I checked the fuses and they are all good...Any Ideas!!??? Its a 99 Gp1200 with AirFilters and Aftermarket Exhaust...


  2. #2
    WATER WOODY's Avatar
    Join Date
    Aug 2005
    Location
    Minden, Nevada, United States
    Posts
    10,664
    +1
    11
    Welcome to GH.
    check kill switch?

  3. #3
    Moderator RX951's Avatar
    Join Date
    Apr 2005
    Location
    League City, Texas
    Posts
    16,066
    +1
    23
    Kill switch? pull the kill pin up and down a few times

  4. #4
    WATER WOODY's Avatar
    Join Date
    Aug 2005
    Location
    Minden, Nevada, United States
    Posts
    10,664
    +1
    11
    Ok PIN.....

  5. #5
    krispaintballz's Avatar
    Join Date
    Sep 2007
    Location
    Kenosha, WI
    Posts
    2,978
    Hold down the mode button on the dash til you see it read "start" or it asks for a code. If you dont have the code I think you can diconnect the blue wire for a couple seconds then put together again. Not sure about the reset some will chime in.

  6. #6
    I tried pulling the Kill Switch up and Down and Still Nothing...

  7. #7
    crashhard's Avatar
    Join Date
    Jul 2007
    Location
    Philly PA, Wildwood NJ, Indialantic FL
    Posts
    2,382
    +1
    24
    hold the mode button down 5 seconds and see if code appears like is says above. That is more then likely your problem if the battery was dead and replaced.

  8. #8
    I just held down Mode and "CODE" came up so I entered it and It said Start but still nothing...I am thinking that its the switch...any one know how much those are?

  9. #9
    john zigler's Avatar
    Join Date
    Aug 2006
    Location
    WI
    Posts
    2,545
    +1
    33
    Quote Originally Posted by Mudweiser View Post
    I just held down Mode and "CODE" came up so I entered it and It said Start but still nothing...I am thinking that its the switch...any one know how much those are?
    alot of times, ( 99%) you can take the switch assembly apart, and jsut clean the contacts. what we find, is when people leave the machines sit, with the tether cord "off", the rubber boot, inside the kill switch, will get distorted, and hold the inner button down, even when you put the tether on.

    i have good used switch assemblies here, if you need one.

    you should always leave the tether cord clipped ON the switch assembly, even when not in use.

    zig

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 1996 polaris sl750 has no power to anything
    By Slauber88 in forum Polaris Projects
    Replies: 3
    Last Post: 06-22-2016, 10:05 PM
  2. question about 4tec no power to guage or anything issue
    By Dieago in forum 4-Tec Performance
    Replies: 0
    Last Post: 08-09-2015, 09:10 AM
  3. Xp no beep or power
    By derwin66 in forum 2-Stroke Performance
    Replies: 12
    Last Post: 03-23-2012, 10:06 PM
  4. No power to anything??
    By monaroman76 in forum 4-Tec Performance
    Replies: 8
    Last Post: 02-23-2012, 04:10 PM
  5. 2007 GTX-L no ignition or power
    By TRADEORHOLD in forum Sea Doo Open Discussion
    Replies: 1
    Last Post: 10-11-2010, 04:38 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •