Page 1 of 5 1 2 3 ... LastLast
Results 1 to 10 of 48
  1. #1
    FLjoyrider's Avatar
    Join Date
    Jul 2007
    Location
    Florida
    Posts
    555

    Custom parts - open for quote requests (have pisser adapters too)

    I now have my CNC mill fully functional (finally) and am open for quote requests on any custom parts made from aluminum plastic stainless, tool steel, etc. I also have a few sets of billet pisser adapters (for fuji engines) for $50 shipped. Flow control set screw optional - just specify.


  2. #2
    thester71's Avatar
    Join Date
    Jun 2009
    Location
    central ma.
    Posts
    1,698
    How about making these one piece adapters for gas valves on a 785
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	attachment.jpg 
Views:	66 
Size:	48.0 KB 
ID:	167010   Click image for larger version. 

Name:	gas valves.jpg 
Views:	54 
Size:	48.0 KB 
ID:	167011  

  3. #3
    FLjoyrider's Avatar
    Join Date
    Jul 2007
    Location
    Florida
    Posts
    555
    Need an isometric view in addition to the above; or maybe a picture of one?

  4. #4
    Canadian Beaver Inspector jkindt's Avatar
    Join Date
    Sep 2009
    Location
    Lethbridge, AB, Canada
    Posts
    1,721
    Pisser adapters would be nice for my wife's ski. Have any pics?

  5. #5
    thester71's Avatar
    Join Date
    Jun 2009
    Location
    central ma.
    Posts
    1,698
    Check out post #23 in my "785 question" thread in general discussion

  6. #6
    FLjoyrider's Avatar
    Join Date
    Jul 2007
    Location
    Florida
    Posts
    555
    I can get some pics of the pissers tonight. So far I have 9 blanks cut out and the mounting holes countersunk.. still have to drill and tap for the 1/4" pipe thread, and also for the flow control set screw. That won't take long I just need to get the jig made to do 6 at once or do them one at a time manually.

    Gas valves - so there are two parts on that diagram then, one round and one oblong. The smaller one on the left won't be hard or too pricey, the other one might be a bit harder. I really need some better drawings to be able to say for sure. Luckily I have low overhead expenses and have bought a used machine for a good price so my up front costs arent as much as a full blown machine shop would have.. although I just broke my first carbide endmill last night and am still kicking myself for it. Should have known better, rapid traverse right through a mounting bolt!! DOH! there goes $50.

  7. #7
    thester71's Avatar
    Join Date
    Jun 2009
    Location
    central ma.
    Posts
    1,698
    I'm not sure where the drawings originated from, but I found them on here.I know if the price was right you could probably sell a few sets on here.

  8. #8
    Moderator beerdart's Avatar
    Join Date
    Aug 2006
    Location
    CT
    Posts
    25,929
    +1
    1,407
    I made the drawing if you need the .DWG shoot me a PM.

  9. #9
    She likes the bike. But the ski gets her wet!!!! xlint89's Avatar
    Join Date
    Oct 2006
    Location
    Cleveland OH
    Posts
    17,330
    +1
    31
    How about a few alignment tools?

  10. #10
    FLjoyrider's Avatar
    Join Date
    Jul 2007
    Location
    Florida
    Posts
    555
    Sorry - no lathe.. only mill. It's the next big thing on my list of stuff to buy.. gas valves are definitely doable for a good price.

    Sorry no pic of the pissers got the kids at 5:30 and havent been able to get to the shop. I will say that they are rather shiny . Finish turned out real good for my manual feeds and speeds. I still have a lot to figure out on the machine - tapping cycles automatic tool changes getting the CAM software to make programs that run so I dont have to edit them.. and of course the monstrous expense of tooling which I have a minimal supply of.
    But progress has been made,

Page 1 of 5 1 2 3 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Replies: 7
    Last Post: 07-10-2015, 01:40 PM
  2. FS Lowered Price for sale I have some 2013 yamaha sho fzr parts
    By Rt-HemiBoY in forum Yamaha Classifieds
    Replies: 21
    Last Post: 01-24-2015, 09:56 AM
  3. Anyone have the Part number for the No Wake / Cruise controls?
    By SilentShooter in forum Yamaha PWC Performance (4-stroke)
    Replies: 17
    Last Post: 06-03-2014, 04:09 PM
  4. Is there a thread or has anyone have a parts list for a type 14 intercooler for a fzr
    By bscpaint in forum Yamaha PWC Performance (4-stroke)
    Replies: 11
    Last Post: 08-30-2013, 11:25 AM
  5. Parts List For 4 Inch Custom Air Intake
    By JFizzleJR in forum 4-Tec Performance
    Replies: 24
    Last Post: 05-15-2007, 05:57 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •