Page 1 of 2 1 2 LastLast
Results 1 to 10 of 19
  1. #1

    i need urgent help with my fzr

    hi every one ....can any one help me??/

    i have worning code in my ski which is code 29 and it's intake pressure sensor,,, i did change the sensor and i did check the wiring all good but i still got the same fault,,, i did change the following:

    1- R & D intake upgrade.
    2- R & D injector.
    3- R & D fuel req.

    and thene i ahde these problem? going crazzy


  2. #2
    yami_rida#26's Avatar
    Join Date
    Oct 2007
    Location
    Cayman Islands
    Posts
    2,112
    I don't think you need injectors and a fuel pressure regulator with all other parts being stock? List what other mods you have done to the ski.

  3. #3
    ok :

    1- R5 INTERCOOLER.
    2- C3 SC WHEEL.
    3- 13/25 PROP.
    4- RIVA POWER FILLTER.
    5- R& D POWER SHOT.
    6- R & D INTAKE UPGRADE FREE FLOW.
    7- RIVA EXGHSUT FREE FLOW.
    8- 525 INJECTOR.
    9- R &D FUEL REG.
    THATS ALL

  4. #4
    IT SAYS IN THE YDS THAT THE INTAKE SENSOR OUT OF SPECS...SO I DID CHANGE IT AND ALSO I DID CHECK THE ORAGE AND THE BLACK AND ORNGE WIRING FOR THE VOLTGE AND IT READ 5V AS THEY REGUIST?????

  5. #5
    IT SAYS IN THE YDS THAT THE INTAKE PREESURE SENSOR OUT OF SPECS...SO I DID CHANGE IT AND ALSO I DID CHECK THE ORAGE AND THE BLACK AND ORNGE WIRING FOR THE VOLTGE AND IT READ 5V AS THEY REGUIST?????

  6. #6
    SHOBiz's Avatar
    Join Date
    Jul 2008
    Location
    Wylie, Texas
    Posts
    3,577
    Did it ever run right with the pink injectors in?

  7. #7
    UMMMM
    i had the ski runing good and then i had to change the clutch so i did order the clutch and the injector but the injector arrived befor the clutch so i did instol them and i went for test but with 4 or 5 psi so it was working good then the clutch arrived so i did instol it and went for test but the check engine came up and when i did use the yds to fined out what is the problem

    i did fined the intake pressure sensor out of specs so i am still trying to solve these out and go for test

  8. #8
    Stop staring at my tits NJJer's Avatar
    Join Date
    Jul 2008
    Location
    This house or that house
    Posts
    1,309
    +1
    1
    Questions

    Did you clear out the codes after installing the new sensor?

    If so, how did you do it?

  9. #9
    yes i got the yamaha diagnose system ,,,and i did erase the code by using it.,,, but it still came up directly

  10. #10
    Stop staring at my tits NJJer's Avatar
    Join Date
    Jul 2008
    Location
    This house or that house
    Posts
    1,309
    +1
    1
    I know a way to clear ECU's in cars/trucks, but I am not sure if I should mention it here as it has not be tested yet to the best of my knowledge.

    One thing about erasing the code, yes, it can be erased, but there will always be a "shadow" of in the ECU. The only way I know to remove it, and most Techs won't ever say this to the "public", is again, not proven on this craft.

    I'll PM anyone who cares to try it. Takes less than a minute. Just don't blame me if the ECU's don't react like car ones do.

    * I myself would try it if I owned the craft. I really don't think it will hurt a thing.

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. ok Polaris pros I need some help with my 1993 sl750
    By Frozen in forum Polaris Open Discussion
    Replies: 8
    Last Post: 07-31-2010, 01:47 PM
  2. in need of help with my gpr
    By Horus in forum Yamaha PWC Performance (2-stroke)
    Replies: 21
    Last Post: 07-20-2010, 01:29 PM
  3. need some help with my mods
    By homebrew in forum 4-Tec Performance
    Replies: 14
    Last Post: 10-15-2009, 10:49 AM
  4. Need some help with my 97 XP
    By midnight08 in forum 2-Stroke Performance
    Replies: 7
    Last Post: 05-27-2009, 07:51 PM
  5. I Need Some Help With My Shark !!!!!!
    By sleblanc in forum Polaris Open Discussion
    Replies: 9
    Last Post: 12-20-2006, 03:17 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •