Results 1 to 6 of 6
  1. #1
    MPower's Avatar
    Join Date
    May 2005
    Location
    Raleigh, NC
    Posts
    3,339
    +1
    121

    J Fizzle updated IC bracket and free flow exhaust

    I searched and could not find pictures of the setup and J Fizzle wasn't sure if it would work so I dove in hoping it would. The bracket sits real low and just barely clears the exhaust exit. It all fits but man there isn't an ass hair to spare...

    The fit wouldn't be as tight if you used a section of the stock rubber exhaust hose because you could rotate the free flow pipe lower, however the owner of this ski wanted an all metal exhaust. It does looks really good and will probably be loud as heck at 3500 RPM.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	0316002135.jpg 
Views:	118 
Size:	176.0 KB 
ID:	178841   Click image for larger version. 

Name:	0317001647.jpg 
Views:	143 
Size:	178.5 KB 
ID:	178842  


  2. #2
    KC Blue Thunder's Avatar
    Join Date
    Oct 2007
    Location
    Jacksonville, Florida
    Posts
    2,079
    looks good, hope you didnt forget to install the rest of the clamps on the intercooler pipes. Jk.

  3. #3
    Eric Ocman's Avatar
    Join Date
    Aug 2008
    Location
    Cataula, Georgia, United States
    Posts
    4,700
    +1
    77
    Quote Originally Posted by Blue Thunder View Post
    looks good, hope you didnt forget to install the rest of the clamps on the intercooler pipes. Jk.
    +1

    Also, Mpower you could take off that 90 elbow and trim it down on each end a tad to make it a bit lower. I just did one for a friend.

  4. #4
    Where did you get that exhaust piping, hoses, and clamps?

  5. #5
    cxracing.com for the pipes and siliconeintakes.com for couplings and clamps

  6. #6
    JFizzleJR's Avatar
    Join Date
    Aug 2005
    Location
    FL
    Posts
    8,628
    +1
    808
    Quote Originally Posted by MPower View Post
    I searched and could not find pictures of the setup and J Fizzle wasn't sure if it would work so I dove in hoping it would. The bracket sits real low and just barely clears the exhaust exit. It all fits but man there isn't an ass hair to spare...

    The fit wouldn't be as tight if you used a section of the stock rubber exhaust hose because you could rotate the free flow pipe lower, however the owner of this ski wanted an all metal exhaust. It does looks really good and will probably be loud as heck at 3500 RPM.
    Thanks for checking on that!

    Quote Originally Posted by Ocman View Post
    +1

    Also, Mpower you could take off that 90 elbow and trim it down on each end a tad to make it a bit lower. I just did one for a friend.
    It's a 45 degree coupler.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 2011 RXT-X and free flow exhaust, SCOM..
    By Pony Racer in forum 4-Tec Performance
    Replies: 1
    Last Post: 04-08-2012, 04:39 PM
  2. 1st time out w/ Riva waterbox and free flow exhaust on 300x
    By cmexeqtu2 in forum Kawasaki PWC Performance (4-stroke)
    Replies: 9
    Last Post: 06-30-2011, 04:14 PM
  3. FS FX SHO/FZR New Blow off valve and free flow exhaust
    By Vagaondracing103 in forum Yamaha Classifieds
    Replies: 0
    Last Post: 08-19-2010, 08:30 AM
  4. Just tested the Riva power filter and free flow exhaust
    By Green Hulk in forum Yamaha PWC Performance (4-stroke)
    Replies: 44
    Last Post: 03-01-2009, 05:18 PM
  5. My 4" Cold Air Intake and free flow pipe...Pix
    By Yuji in forum 4-Tec Performance
    Replies: 7
    Last Post: 06-10-2005, 05:11 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •