Thread: Throttle Body Spray Kit....
09-14-2006, 10:31 AM #1
Throttle Body Spray Kit....
I was wondering about this kit. is it worht it? Right now my TB is getting stuck and I have to tap it a few tims on the throttle lever to unstick it. I was told this kit would take care of the problem if it isn't too late.
How is the install on these? Hard, moderate? I know you have to drill into the TB...? How's that?
Should I take out the TB and give it a nice clean and lube? How do I take it off? I know there are some torx screws but I see a lot more attached to it.
Any info appreciated.
09-14-2006, 10:41 AM #2
- Join Date
- Aug 2006
Their are 4 torx screw that can be remove easily and 2 electric cable clips to remove also then the unit is free.
The unit is easy to work on and a good clean will do it wonders.
Its a NO Brainer!
09-14-2006, 11:14 AM #3
I thought the hose on mine was for fogging it for winter. I guess I would rather have it, then not have it. It is just a little hose with a cap on it. If you are taking the T/B off, now would be the time to put the KIT on I guess.
09-14-2006, 11:25 AM #4
where do you get the kit at? when did they start putting these on?
09-14-2006, 11:51 AM #5
You can just get a kit to put on??
They started putting this port on the 06' throttle bodys....
Last edited by Gforce; 09-14-2006 at 01:15 PM.
09-14-2006, 01:08 PM #6
gotcha yea i want a kit then cause i ride a lot in the salt even though i lube the whole motor after a ride
09-14-2006, 01:25 PM #7Originally Posted by RXP Steve
09-14-2006, 03:29 PM #8
I am assuming it is hard to get a can down to the throttle body and spray it inside. A port sounds like a great idea for fogging and cleaning the throttle body.
Here is some information on the AMSOIL Throttle Body Cleaner and Fogging Oil
AMSOIL Power Foam Engine Cleaner & Degreaser
Improves starting and performance. Cleans dirty intake systems and spark plugs, frees sticky valves. This is safe for two-cycle and four-cycle engines. This works great on cleaning off power valves also.
Here is the Fogging oil from AMSOIL. It acts as a barrier that keeps condensation from coming into direct contact with steel and iron components, that forms surface corrosion on cylinder liners, piston rings, anti-friction bearings and steel/iron contact surfaces on rotational seals.
09-14-2006, 08:19 PM #9
Good info guys thanks a lot.
09-15-2006, 12:23 AM #10
Now I need to know the difficulty of intalling the TB lube kit?
I'd hate to have to pay $75 to have it installed when the kit is only $25. Yet again, I dont wanna mess the TB up and have to spend $900 for a new one!
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
FS - Parts throttle body and nos kitBy cliff0413 in forum Sea Doo ClassifiedsReplies: 3Last Post: 02-16-2013, 01:08 PM
By Green Hulk in forum 4-Tec PerformanceReplies: 61Last Post: 09-10-2007, 01:01 PM
By Jarrett in forum 4-Tec PerformanceReplies: 6Last Post: 05-29-2006, 12:40 AM
By 01xdime in forum 4-Tec PerformanceReplies: 21Last Post: 10-06-2005, 11:22 AM
By 1 FAST VE in forum 4-Tec PerformanceReplies: 2Last Post: 08-18-2005, 10:45 AM