Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11
  1. #1

    Stage II plus ECU reflash

    I did my initial couple of runs after getting back my FZR with a stage II kit and re-flash from R & D. Fastest run was 78.3 gps on a full tank of gas. I believe with a few tweaks I can get to 80 mph.

    One thing I did experience was some porpoising on top end (which is probably why I didn't hit 80). Any ideas how to curb that? I was running one notch down on the VTS trim.

    The throttle response and acceleration is unreal!!!


  2. #2
    Site Admin Green Hulk's Avatar
    Join Date
    Apr 2005
    Location
    Morgan City, LA
    Posts
    36,398
    +1
    2,524
    Quote Originally Posted by tadam View Post
    One thing I did experience was some porpoising on top end
    Put some .020 shims on the back two bolts between ride plate and hull.

    If it still bounces go with .030

  3. #3
    Will that my deter my quest for 80 mph?

  4. #4
    fx160's Avatar
    Join Date
    Nov 2005
    Location
    gold coast australia
    Posts
    2,409
    +1
    193
    yes
    but you still have the stock ride plate acording to your sig
    so fit a vx plate and you may be at 80 straight away
    or an R&D plate

    kev

  5. #5
    gordon lasiter #328's Avatar
    Join Date
    Aug 2008
    Location
    katy, texas , United States
    Posts
    1,647
    +1
    28
    Quote Originally Posted by fx160 View Post
    yes
    but you still have the stock ride plate acording to your sig
    so fit a vx plate and you may be at 80 straight away
    or an R&D plate

    kev
    +1.

  6. #6
    hitman's Avatar
    Join Date
    Aug 2006
    Location
    Ft. Lauderdale, FL
    Posts
    4,328
    +1
    12
    What prop are you running and what RPM are you turning?

  7. #7
    I have a full stage II kit from R&D:
    R&D C3 Monster Charger Kit
    Part # 612-25003
    R&D Pro Limited Intercooler Kit
    Part # 612-18004
    R&D Greddy Surge Protector
    Part # 613-95261
    R&D Powershot Fuel Tuner & Boost Unlimiter
    Part # 802-18000
    R&D Power Core Intake Manifold Sleeve
    Part # 612-17998
    R&D FZ/FZR 13/25 Pro Pitch Impeller
    Part # 132- 01325
    R&D FZR Aquavein Intake Grate
    Part # 112-18001
    R&D Pump Shoe Seal Kit
    Part # 162-00007
    R&D FZ/FZR Pro Series Ride Plate
    Part # 122-18001
    R&D FZ/FZR Anti-Cavitation Cone
    Part # 162-18000
    R&D Mutli-Port Boost Adaptor
    Part # 612-92005
    R&D FZ/FZR High Flow Exhaust Kit
    Part # 332-18000
    R&D FZ/FZR Power Plenum Filter Kit
    Part # 200-01801
    R&D Engine/Intercooler Cooling Kit
    Part # 660-18001

    I have not checked my RPMs as I only had it out once since I got it back. I updated my sig.
    Last edited by poleski; 04-24-2010 at 08:55 AM. Reason: new sig

  8. #8
    hitman's Avatar
    Join Date
    Aug 2006
    Location
    Ft. Lauderdale, FL
    Posts
    4,328
    +1
    12
    You need to know what RPM you're turning to see how well your prop is dialed in. If you're not turning around 83-8400 rpm you're leaving power and speed on the table.

  9. #9
    My stock tach bottoms out a 8. Where do I get an aftermarket tach and can it replace my stock to fit?

  10. #10
    hitman's Avatar
    Join Date
    Aug 2006
    Location
    Ft. Lauderdale, FL
    Posts
    4,328
    +1
    12
    Quote Originally Posted by tadam View Post
    My stock tach bottoms out a 8. Where do I get an aftermarket tach and can it replace my stock to fit?
    This is a very good tach that Jerry sells in the store. It is more expensive than other cheaper tachs but it is well worth the money.

    http://www.4-tecperformance.com/inde...roducts_id=308

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. life of motor with stage II and ECU????????
    By Jrsrxp in forum 4-Tec Performance
    Replies: 6
    Last Post: 09-30-2006, 09:04 AM
  2. Stage II loking to upgrage ECU ~Need feedback~
    By Alex13 in forum 4-Tec Performance
    Replies: 1
    Last Post: 08-10-2006, 04:37 PM
  3. Riva Stage II w/ Rotax ECU
    By INDY27 in forum 4-Tec Performance
    Replies: 38
    Last Post: 04-10-2006, 10:45 AM
  4. How are your Riva RXP Stage II's running for you?
    By Jarrett in forum 4-Tec Performance
    Replies: 47
    Last Post: 10-26-2005, 10:36 AM
  5. Replies: 4
    Last Post: 07-14-2005, 09:38 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •