Page 1 of 2 1 2 LastLast
Results 1 to 10 of 17
  1. #1

    Super Charger PINS

    I have an RXP I had to take off the supercharger and when taking it apart a bunch of pins flew out now I don't know where they go.. Anyone have a clue ?


  2. #2
    Got Boost? psycho rxp's Avatar
    Join Date
    Jul 2005
    Location
    Port St. Lucie, FL
    Posts
    5,445
    +1
    182
    Quote Originally Posted by italybooze View Post
    I have an RXP I had to take off the supercharger and when taking it apart a bunch of pins flew out now I don't know where they go.. Anyone have a clue ?

    Sounds like the needle bearings under the Gear.

    Gonna need to rebuild the charger, and get all of them out of your motor. There should be 40 total

  3. #3
    Would I be able to put them back ?

  4. #4
    Out of my motor how do I do that ????

  5. #5
    Got Boost? psycho rxp's Avatar
    Join Date
    Jul 2005
    Location
    Port St. Lucie, FL
    Posts
    5,445
    +1
    182
    Quote Originally Posted by italybooze View Post
    Would I be able to put them back ?

    No, they should be replaced..

    Here's some info on SC failures, and what to do.
    http://www.greenhulk.net/forums/show...washer+failure

  6. #6
    Vern's Avatar
    Join Date
    May 2005
    Location
    Grand Haven, MI
    Posts
    3,594
    +1
    128
    You need to clarify ... did you pull the SC, then, when taking it apart that the pins fell out? If that is the case, its no biggie, you can get the pins separately, or just do a full rebuild. If the pins fell out into the motor AS you were removing the SC, that is different ... then the motor should be removed and taken apart until all 40 pins/bearings are found.

  7. #7
    Got Boost? psycho rxp's Avatar
    Join Date
    Jul 2005
    Location
    Port St. Lucie, FL
    Posts
    5,445
    +1
    182
    Quote Originally Posted by Vern View Post
    You need to clarify ... did you pull the SC, then, when taking it apart that the pins fell out? If that is the case, its no biggie, you can get the pins separately, or just do a full rebuild. If the pins fell out into the motor AS you were removing the SC, that is different ... then the motor should be removed and taken apart until all 40 pins/bearings are found.

    Vern, here is his charger...



    Ski was sunk, and now has sat a year...

  8. #8
    If i knew,...I wouldn't ask sea-one's Avatar
    Join Date
    Aug 2009
    Location
    Dallas/Waxahachie
    Posts
    2,340
    +1
    109
    Dude that is fudged up! and the motor is most likely junk

  9. #9
    GOT BOOST? Dockside's Avatar
    Join Date
    Dec 2008
    Location
    Ontario, Canada
    Posts
    3,879
    +1
    116
    im guessing theres more to this story....

  10. #10
    Yah it is probably fukd but Idk it cranks and is ready to kick over but doesn't .. So what do you think I should buy a sbt motor or try and rebuild mine or try and find a used engine ??

    I might just do the swap it shouldn't be to hard should it ?

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. new super charger
    By stickem in forum 4-Tec Performance
    Replies: 125
    Last Post: 03-06-2007, 01:50 AM
  2. Super Charger Clutch Workings
    By brad2510 in forum 4-Tec Performance
    Replies: 17
    Last Post: 03-02-2006, 01:16 PM
  3. super charger from les
    By stickem in forum 4-Tec Performance
    Replies: 0
    Last Post: 02-22-2006, 02:48 PM
  4. Removing Super Charger
    By wwalker in forum 4-Tec Performance
    Replies: 9
    Last Post: 07-06-2005, 01:36 PM
  5. Frustrated With Super Charger
    By Cutter in forum 4-Tec Performance
    Replies: 66
    Last Post: 07-01-2005, 12:34 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •