Results 1 to 6 of 6
  1. #1
    Beerme's Avatar
    Join Date
    Nov 2007
    Location
    Hurricane Ally aka Polk county, Auburndale Florida.
    Posts
    69

    07 GP1300R D-Plate Questions

    Ok, in doing the search I found the below thread. So am I correct in thinking the only thing I need to buy in order to convert from a Cat to D-Plate is the D-Plate?

    http://greenhulk.net/forums/showthre...ht=gp1300r+cat

    Do I need the Riva efi controller or any other parts besides the D-Plate? Secondly, if I install the D-Plate and still have factory Oil Injection, can I start using other TCW3 oil such as Penzoil Marine 2 Stroke oil which is half the price of Yamalube?

    Thanks in advance,
    Happy Floating....


  2. #2
    Hydrotherapy's Avatar
    Join Date
    Sep 2006
    Location
    The Rock
    Posts
    3,347
    +1
    17
    the 05 and above needs a home made chip to stop them all beeping,some dont need anything but im pretty sure you can use either 2k ohm or 10k ohm resistor in line to stop the BEEP

    for the other part of your question... read first sticky "do i need a fuel controler"....its been covered and you may find it a good read

  3. #3
    New ski! Markb47's Avatar
    Join Date
    Apr 2008
    Location
    Ireland
    Posts
    312
    As Hydrotherapy says read "do i need efi controller". The EFI controller is usually only needed tho if you increase the timing

    If you are installing the d plate tho you can use any 2 stroke oil in the ski and not just yamalube.

  4. #4
    Happily Self-Employed WFO's Avatar
    Join Date
    Nov 2005
    Location
    Houston, Texas
    Posts
    12,801
    +1
    450
    Quote Originally Posted by Beerme View Post
    Ok, in doing the search I found the below thread. So am I correct in thinking the only thing I need to buy in order to convert from a Cat to D-Plate is the D-Plate?

    http://greenhulk.net/forums/showthre...ht=gp1300r+cat

    You may not need a chip on that year, but if the sensor goes off, you will need to wire in a 2K or 2.2K resistor

    Do I need the Riva efi controller or any other parts besides the D-Plate?

    no

    Secondly, if I install the D-Plate and still have factory Oil Injection, can I start using other TCW3 oil such as Penzoil Marine 2 Stroke oil which is half the price of Yamalube?

    yes

    Thanks in advance,
    Happy Floating....
    ^

  5. #5
    R1SideWayz's Avatar
    Join Date
    Jul 2005
    Location
    avondale,az
    Posts
    125
    +1
    1
    I will say it varies machine to machine if an EFI is required. When I installed my D-plate it bogged really bad on the bottom. I didn't really want to spend 350.00 on an EFI controller, so I had a piece of steel welded to the opening of the plate.

  6. #6
    Beerme's Avatar
    Join Date
    Nov 2007
    Location
    Hurricane Ally aka Polk county, Auburndale Florida.
    Posts
    69
    Thanks everyone for the insight.....

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 07 RXP ride plate question
    By RXPteamtimebomb in forum Sea Doo Open Discussion
    Replies: 9
    Last Post: 03-14-2015, 10:47 PM
  2. GP1300R Ride Plate Questions
    By El_Conquistador_Trav in forum Yamaha Open Discussion
    Replies: 0
    Last Post: 07-08-2014, 03:50 PM
  3. 07 GP1300R w/D-plate
    By fcs1965 in forum Yamaha PWC Performance (2-stroke)
    Replies: 1
    Last Post: 04-21-2009, 05:35 PM
  4. 07 GP1300R D-plate
    By Tanny in forum Yamaha PWC Performance (2-stroke)
    Replies: 20
    Last Post: 04-12-2007, 07:16 PM
  5. Another D-Plate question!
    By Chrisrokc in forum Yamaha PWC Performance (2-stroke)
    Replies: 2
    Last Post: 06-20-2006, 03:06 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •