Page 1 of 4 1 2 3 ... LastLast
Results 1 to 10 of 38
  1. #1

    how many psi should the tank holds?

    i have a low hesitation, im thinking it could be the tank not holding pressure, how many psi should it hold?thanx


  2. #2
    She likes the bike. But the ski gets her wet!!!! xlint89's Avatar
    Join Date
    Oct 2006
    Location
    Cleveland OH
    Posts
    17,329
    +1
    31
    Tank should release pressure over 1.5 psi.

  3. #3
    where could it release the pressure? on the vents?

  4. #4

    Join Date
    Jul 2010
    Location
    Mt carroll, IL
    Posts
    91
    yes one of the lines on the tank goes to a check valve.

  5. #5
    1 valve of mine is broken , is it ok to block the 1 vent, and only 1 i am using? vent only accepts air outside right? and not letting air going outside?

  6. #6
    i got a 1 valve on my tank, the other valve is losts, so how would i know if i have the IN valve or the OUT valve???

  7. #7
    blegan's Avatar
    Join Date
    May 2008
    Location
    bakersfield
    Posts
    321
    Quote Originally Posted by andy95'slx780 View Post
    1 valve of mine is broken , is it ok to block the 1 vent, and only 1 i am using? vent only accepts air outside right? and not letting air going outside?
    No one is pressure relief & one is for vaccum relief. Both should pop at 1.5 p.s.i. as previously stated.

  8. #8
    She likes the bike. But the ski gets her wet!!!! xlint89's Avatar
    Join Date
    Oct 2006
    Location
    Cleveland OH
    Posts
    17,329
    +1
    31
    Quote Originally Posted by blegan View Post
    No one is pressure relief & one is for vaccum relief. Both should pop at 1.5 p.s.i. as previously stated.
    Actually the "vacuum relief" should open immediately. you don't want ANY vacuum created in the tank.

  9. #9
    She likes the bike. But the ski gets her wet!!!! xlint89's Avatar
    Join Date
    Oct 2006
    Location
    Cleveland OH
    Posts
    17,329
    +1
    31
    Quote Originally Posted by andy95'slx780 View Post
    i got a 1 valve on my tank, the other valve is losts, so how would i know if i have the IN valve or the OUT valve???
    IN valve is 2 tone in color.

    The OUT valve is all black.

    Post a pic for verification though.

  10. #10
    i got this one left....


Page 1 of 4 1 2 3 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. How many psi of compression should a gti 130 have???
    By BlownChevy254 in forum 4-Tec Performance
    Replies: 7
    Last Post: 03-26-2014, 08:18 AM
  2. how many hours should the new stator pump bearings last?
    By andy95'slx780 in forum Yamaha PWC Performance (4-stroke)
    Replies: 1
    Last Post: 01-01-2012, 10:40 PM
  3. How many hrs should I wait to install the 4" intake?
    By Rutcutter in forum 4-Tec Performance
    Replies: 18
    Last Post: 03-21-2011, 10:22 PM
  4. Replies: 6
    Last Post: 08-02-2010, 10:01 PM
  5. How many hours to a tank of gas?
    By Gforce in forum Sea Doo Open Discussion
    Replies: 12
    Last Post: 11-26-2005, 09:09 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •