08-21-2010, 01:27 AM #1
FZS - Hull wear after only 10 hours ?? help
any one can tell me is this normal.
the middle of the hull has gone after 10 houers of riding.
we put the ski in water from beach.. power sand beach.. and also bring it op from the beach..
now the middle body work is gone and some long rift or hole has appred???
is this normal?
Can one get someting to attach there for protecting the skill hull from more wear..
it looks like there are bolts and holes in the rift for fitting something..
its my first SKI!! so im a newbi.. please help me out
08-21-2010, 01:39 AM #2
its normal to have a little wear on the bottom if you land on the beach but iv never seen it as bad as that has it been on and off the beach for 10 hours non stop
08-21-2010, 01:59 AM #3
we land the ski on the beach like 30 times total.
means drive the ski and cut engine just before you hit sand, and it will slide just a bit op on the beach..
So we can go relax in the sun untill next ride..
i was told thats normal to land the craft this way on a non stone beach.. the sand is power like "patong beach, thailand"
Whats the long hole, rift thing i can see now its been wared down a bit??
is there no beach landing protechtion thing to maunt down in that rift or some thing??
08-21-2010, 02:07 AM #4
You can get a keelgaurd, but it looks like you are a little beyond that.
08-21-2010, 02:08 AM #5
i dont think there is anything you could put on it would efect the handling
08-21-2010, 02:09 AM #6
I would never do that with a ski... Buy a anchor or sand anchor!
08-21-2010, 02:33 AM #7
I think your smashing it up to the beach mate!!
Thats some wear!
Remember Baywatch was in the 90's this is 2010!!! Look after it!
08-21-2010, 02:42 AM #8
08-21-2010, 02:45 AM #9
keelgaurd.. what brand is the best??
So get it repared, new fiberglass, and then add keelgaurd???
Well i do look after my ski, really well..
if the hull is so weak, that after 10 hours riding, and putting it on the beach for 30 times... then yamaha has a big problem whith there nano del hull lalala.
then its a load of BS... my friend has a seadoo, he beaching his for years, and it dos not have the same wear at all.
and that's on a danish beach whit more ruff sand!!
I also wonder why there is a RIFT there, like a long rift as you see in the picture, inside it has some bolts and stuff..
what the hell are those for?
and how do one use those when the hull is intact, you cant reach them???
08-21-2010, 02:50 AM #10
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
By TIBFIB in forum 4-Tec PerformanceReplies: 19Last Post: 07-01-2010, 08:37 AM
By jack in forum 4-Tec PerformanceReplies: 12Last Post: 11-27-2005, 03:39 PM
By 01xdime in forum 4-Tec PerformanceReplies: 13Last Post: 08-18-2005, 04:16 PM
By RXPDAVID in forum 4-Tec PerformanceReplies: 11Last Post: 08-15-2005, 06:04 PM
By Jrsrxp in forum Sea Doo Open DiscussionReplies: 2Last Post: 07-11-2005, 05:38 PM