Page 1 of 2 1 2 LastLast
Results 1 to 10 of 17

Thread: Shred Master

  1. #1
    MR. SCOVILLE UNIT SUCKMYWAKE's Avatar
    Join Date
    Aug 2005
    Location
    ASTON, PENNSYLVANIA
    Posts
    2,836
    +1
    8

    Shred Master

    Has Anyone Tried The Shred With The Angle Mod We All Know And Love? Or Tried Shimming It. I Would Like To Try A Shred But Nobody Seems To Have One.


  2. #2
    HopatcongGPR's Avatar
    Join Date
    Feb 2006
    Location
    New Jersey
    Posts
    1,114
    Quote Originally Posted by SUCKMYWAKE View Post
    Has Anyone Tried The Shred With The Angle Mod We All Know And Love? Or Tried Shimming It. I Would Like To Try A Shred But Nobody Seems To Have One.

    i shimmed it,,,,i did consider angle moding it...but it does not have the same angle as the r & d plate. plus i didnt want to creame a 400 dollar plate in case it didnt work,,,,so i could at least sell it...as i did for a woping 180 bucks on ebay!








    as you can see in these phots,,,the shread is basicly an extension of the hull. it follows essentially the same angle of the hull OR the tail is slightly kicked DOWNward.







    back in the day,,,speaking with carl,,,we considered hacking off that long tale and angle modding it....my wallet didnt allow me to hack it up.

    i will say,.,,,you would have LOVED a shread when we rode a few weeks back....it kicks a$$ in the rough. i wish i kept it for that reason alone....then again,,,,as i said to BOB i would rather have a shread for my XLT!

    it also LOVED a 1200 grate with the outer wings CUT OFF! i still have this hacked up grate,,,, if you get a shread,,,ill be glad to send it down for you to tryyyyyyyyyyyy. dont bother with a worx grate as bob recommends,,,,it simply $ucked.



    ENJOY!

    ahhhhh,,,,isnt he cute?

    Last edited by HopatcongGPR; 10-21-2006 at 08:04 AM.

  3. #3
    MR. SCOVILLE UNIT SUCKMYWAKE's Avatar
    Join Date
    Aug 2005
    Location
    ASTON, PENNSYLVANIA
    Posts
    2,836
    +1
    8
    yorkie poo? so does anyone have a shred??? thanks for info dan

  4. #4
    philip_gpr's Avatar
    Join Date
    Dec 2005
    Location
    Canada
    Posts
    2,724
    +1
    3
    save the $400 and just use the stock plate

    seriously it is hard to tell them apart

    but I will say the best rough handling set-up I have ever used was the following

    Shred plate
    R&D tabs shimmed down 3 mm
    "0" degree Riva nozzle
    Skat full swirl impeller with 05 pump and 2 in extension

    everytime someone posts the package handles rough water well I laugh - until you have ridden a ski properly set-up for the rough stuff you just have no idea how good it can really be

  5. #5
    philip_gpr's Avatar
    Join Date
    Dec 2005
    Location
    Canada
    Posts
    2,724
    +1
    3
    as far as the angle mod goes there is actually not that much material on the mounts, so you really can't remove that much - yes you could beef it up with some welding but that would just add to the cost

  6. #6
    HopatcongGPR's Avatar
    Join Date
    Feb 2006
    Location
    New Jersey
    Posts
    1,114
    Quote Originally Posted by philip_gpr View Post
    as far as the angle mod goes there is actually not that much material on the mounts, so you really can't remove that much - yes you could beef it up with some welding but that would just add to the cost
    did u dump your shred plate?

  7. #7
    MR. SCOVILLE UNIT SUCKMYWAKE's Avatar
    Join Date
    Aug 2005
    Location
    ASTON, PENNSYLVANIA
    Posts
    2,836
    +1
    8
    i'm not looking to get a rough water set-up. although i am sure the shred would be it. philip, dan, i took my stock plates with me to shipbottom just for that reason. when we left it wasnt rough at all, shortly into the trip and on the way back i was coming unhooked every wave

  8. #8
    philip_gpr's Avatar
    Join Date
    Dec 2005
    Location
    Canada
    Posts
    2,724
    +1
    3
    yes I still have the shred

    I don't think you could ever get a shred to top a R&D plate that has been prepped properly

  9. #9
    MR. SCOVILLE UNIT SUCKMYWAKE's Avatar
    Join Date
    Aug 2005
    Location
    ASTON, PENNSYLVANIA
    Posts
    2,836
    +1
    8

    Talking

    darn u philip, send me the shred( for testing) i will not modify it in any way. and i will send u my kerry(personally hand tuned )and highly polished by me ,r+d package plate for collateral

  10. #10

    Join Date
    Mar 2006
    Location
    Burlington,NC
    Posts
    193
    Will the shredmaster outperform the stock plate set up for a all around type of ride? Don't want to lose my all around performance but would love some extra mph.

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. FS 105 Ultra Shred Master ride plate and R&D intake Solas Intake
    By enhanced250 in forum Kawasaki Classifieds
    Replies: 5
    Last Post: 09-08-2010, 05:39 AM
  2. What happened to the shred master 15F/stxr
    By jonny5 in forum Kawasaki Open Discussion
    Replies: 4
    Last Post: 10-31-2009, 07:09 PM
  3. WTB - Shred Master Plate
    By Mik72e in forum Yamaha Classifieds
    Replies: 0
    Last Post: 07-05-2008, 12:45 AM
  4. Shred Master first impressions
    By izz0 in forum Yamaha Open Discussion
    Replies: 11
    Last Post: 02-07-2008, 09:57 PM
  5. Shred master ride plate
    By snoopy in forum Yamaha PWC Performance (2-stroke)
    Replies: 2
    Last Post: 04-08-2006, 10:44 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •