Page 1 of 4 1 2 3 ... LastLast
Results 1 to 10 of 31
  1. #1
    Orlando Shark's Avatar
    Join Date
    Mar 2009
    Location
    Miami, FL
    Posts
    2,419
    +1
    10

    Turbo guys: Where can I find the T Fitting to feed the turbo oil?

    Hey guys, I'm almost done with my turbo but i'm trying to figure out where I can find a T Fitting for the oil line to the turbo. I am trying to T from the oil sensor right under the trottle body.

    The line that will fee the Turbo will be a 4AN.

    Anyone have any suggestions? I am trying to get it by the weekend so I can finally ride!

    Thanks.


  2. #2
    HighPSI's Avatar
    Join Date
    Jun 2008
    Location
    Melbourne, FL
    Posts
    410
    I don't know if the '06 restricts the oil to the head, but I fed my turbo on my RXP-X from the fitting in the head near the oil filter.

  3. #3
    R88ory RXP's Avatar
    Join Date
    Feb 2008
    Location
    Kent, England
    Posts
    2,737
    +1
    46
    You need a 1/8npt t piece and a male to male adaptor to screw into the block then the T piece ontop that with the press sensor on 1 side and feed to turbo on the other.

    Search the net there will be a mail order supplier.

    R88

  4. #4
    Orlando Shark's Avatar
    Join Date
    Mar 2009
    Location
    Miami, FL
    Posts
    2,419
    +1
    10
    Thanks guys.

  5. #5
    home of the dislexic fingers breon's Avatar
    Join Date
    Aug 2007
    Location
    port st lucie fl
    Posts
    3,471
    this might help i just ordered all my fittings from them formy intercooler heat exchanger ect..

    http://www.discounthydraulichose.com/

  6. #6
    Orlando Shark's Avatar
    Join Date
    Mar 2009
    Location
    Miami, FL
    Posts
    2,419
    +1
    10
    Quote Originally Posted by breon View Post
    this might help i just ordered all my fittings from them formy intercooler heat exchanger ect..

    http://www.discounthydraulichose.com/
    Thanks Breon, I'll check it out.

    I'm thinking of getting the oil from where Highpsi recommended.

    Just a question for anyone that has done that. Do you get the proper oil pressure tapping that? Does it flow more/less oil? I'll post a pic of the spot a bit later.

  7. #7
    2006 Turbo RXP boBO's Avatar
    Join Date
    Mar 2008
    Location
    STATE OF KUWAIT
    Posts
    1,034
    +1, Same location om my turbo


    Quote Originally Posted by HighPSI View Post
    I don't know if the '06 restricts the oil to the head, but I fed my turbo on my RXP-X from the fitting in the head near the oil filter.

  8. #8
    Turbo Doo's from Down Under one1one's Avatar
    Join Date
    Aug 2007
    Location
    Gold Coast, Australia
    Posts
    394
    Quote Originally Posted by R88ory RXP View Post
    You need a 1/8npt t piece and a male to male adaptor to screw into the block then the T piece ontop that with the press sensor on 1 side and feed to turbo on the other.
    What he said.

  9. #9
    Orlando Shark's Avatar
    Join Date
    Mar 2009
    Location
    Miami, FL
    Posts
    2,419
    +1
    10
    These are the two places I was thinking of getting oil from:

    Are these the spots you guys are talking about?

    Click image for larger version. 

Name:	085.jpg 
Views:	106 
Size:	102.7 KB 
ID:	213648Click image for larger version. 

Name:	092.jpg 
Views:	125 
Size:	64.4 KB 
ID:	213647

  10. #10
    Nothin' better than Doo'in it! BigDaddyRXP's Avatar
    Join Date
    Aug 2007
    Location
    Tampa Bay, FL
    Posts
    9,202
    +1
    673
    Quote Originally Posted by ImAShark View Post
    Are these the spots you guys are talking about?
    I don't think so... I believe these guys are using the port on the cylinder head. Check out the top of this picture......

    Click image for larger version. 

Name:	123.jpg 
Views:	116 
Size:	159.2 KB 
ID:	213654

    This location would not be good for an 04-05 due to the oil restricter in the block on those models... unless you pull the restricter from the block and run an 06+ rocker shaft.

Page 1 of 4 1 2 3 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Where can I find some black insert for the bumper rail.
    By sn-95 in forum Sea Doo Open Discussion
    Replies: 7
    Last Post: 07-17-2011, 09:38 PM
  2. Where Can I Find This Handle Bar Endcaps
    By 97GPSLEEPER in forum Yamaha PWC Performance (2-stroke)
    Replies: 9
    Last Post: 01-06-2007, 11:10 AM
  3. Where can i find this part
    By DeeGee in forum Sea Doo Open Discussion
    Replies: 3
    Last Post: 07-03-2006, 02:55 PM
  4. Where do i find the engine compartment vents?
    By lawracing in forum Sea Doo Open Discussion
    Replies: 3
    Last Post: 06-18-2006, 07:54 PM
  5. where Can I buy the right pump to change oil?
    By CarFanatic in forum Sea Doo Open Discussion
    Replies: 9
    Last Post: 05-31-2006, 06:27 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •