Results 1 to 7 of 7
  1. #1
    svtnos's Avatar
    Join Date
    Aug 2007
    Location
    Almont MI
    Posts
    316
    +1
    1

    how to prime/bleed the oil lines

    i jsut replaced the oil injection lines on my 95 xp..how do i go about bleeding or priming the system??


  2. #2
    RumRunnerRon's Avatar
    Join Date
    Mar 2010
    Location
    Portland, Oregon
    Posts
    462
    Quote Originally Posted by svtnos View Post
    i jsut replaced the oil injection lines on my 95 xp..how do i go about bleeding or priming the system??




    There is a bleed screw on the pump which will allow you to bleed the supply line to the pump. After that to bleed the injection lines you manually hold the oil pump linkage/lever in the wot position while idling the engine.

  3. #3
    flyin' the friendly skies airbornexp's Avatar
    Join Date
    Aug 2007
    Location
    Mahomet, Il. USA
    Posts
    6,004
    +1
    163
    make sure that you premix the first couple gallons while you are doing this...keep the cylinders lubed or your doing another top end

  4. #4
    RumRunnerRon's Avatar
    Join Date
    Mar 2010
    Location
    Portland, Oregon
    Posts
    462
    Quote Originally Posted by airbornexp View Post
    make sure that you premix the first couple gallons while you are doing this...keep the cylinders lubed or your doing another top end


    Nice add Air. Hadn't thought of that.

  5. #5
    flyin' the friendly skies airbornexp's Avatar
    Join Date
    Aug 2007
    Location
    Mahomet, Il. USA
    Posts
    6,004
    +1
    163
    No Problem....been there, done that

  6. #6
    svtnos's Avatar
    Join Date
    Aug 2007
    Location
    Almont MI
    Posts
    316
    +1
    1
    oops

  7. #7
    2000 GPRXP 4tec shooter98xpl's Avatar
    Join Date
    Dec 2005
    Location
    Charleston SC
    Posts
    2,717
    +1
    3
    Or, pull your spark plugs out, pull throttle wide open and turn the motor over till the oil lines fill up. Remember, 10 seconds on, then 10 seconds off so you don't wear the starter out.
    SHOOTER

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. How to change ultra 150 oil lines
    By eVolution54 in forum Kawasaki PWC Performance (2-stroke)
    Replies: 0
    Last Post: 07-17-2011, 09:49 PM
  2. Replies: 4
    Last Post: 06-17-2011, 03:40 PM
  3. How do I bleed the oil pump on a '98 XL1200
    By wakehopper in forum Yamaha How To & FAQs
    Replies: 3
    Last Post: 11-10-2010, 10:40 AM
  4. how to prime oil system again? sorry ha
    By Stagesrt4 in forum 2-Stroke Performance
    Replies: 10
    Last Post: 06-28-2010, 12:16 PM
  5. HOW DO YOU - Bleed the fuel lines???
    By BartenderSmalley in forum 2-Stroke Performance
    Replies: 10
    Last Post: 08-24-2008, 08:51 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •