Results 1 to 10 of 10
  1. #1
    abie_lah's Avatar
    Join Date
    Jul 2009
    Location
    Kuala Terengganu, Malaysia
    Posts
    264

    c3 s/c cluth setup??

    how much tork to set cluth at c3 s/c with oem cluth and spring washer??


  2. #2
    GOT BOOST? Dockside's Avatar
    Join Date
    Dec 2008
    Location
    Ontario, Canada
    Posts
    3,879
    +1
    116
    I set mine to 11flbs and after 10 hrs it was at 10.5flbs and 50 hrs later its still at 10.5flbs...

  3. #3
    R88ory RXP's Avatar
    Join Date
    Feb 2008
    Location
    Kent, England
    Posts
    2,737
    +1
    46
    Quote Originally Posted by Dockside View Post
    I set mine to 11flbs and after 10 hrs it was at 10.5flbs and 50 hrs later its still at 10.5flbs...
    +1 on what dockside said. A good rule of thumb is to have 1pound of slip for every 1 psi of boost you want to make. R88

  4. #4
    abie_lah's Avatar
    Join Date
    Jul 2009
    Location
    Kuala Terengganu, Malaysia
    Posts
    264
    if i use rnd s/c cluth??

  5. #5
    Moderator Snoman's Avatar
    Join Date
    Apr 2006
    Location
    South Chicagoland
    Posts
    14,688
    +1
    846
    Quote Originally Posted by abie_lah View Post
    if i use rnd s/c cluth??
    The same, Like Rory said:

    1pound of slip for every 1 psi of boost

  6. #6
    R88ory RXP's Avatar
    Join Date
    Feb 2008
    Location
    Kent, England
    Posts
    2,737
    +1
    46
    Quote Originally Posted by abie_lah View Post
    if i use rnd s/c cluth??
    Yes the same will apply no matter what washers you are using. R88

  7. #7
    abie_lah's Avatar
    Join Date
    Jul 2009
    Location
    Kuala Terengganu, Malaysia
    Posts
    264
    huhuhuu,, my tork wrench only read at ftlb and nm,, know after i change a new rnd cluth,,my c3 s/c slip at 14nm or 10.3ftlb,, its ok????

  8. #8
    Moderator Snoman's Avatar
    Join Date
    Apr 2006
    Location
    South Chicagoland
    Posts
    14,688
    +1
    846
    Quote Originally Posted by abie_lah View Post
    huhuhuu,, my tork wrench only read at ftlb and nm,, know after i change a new rnd cluth,,my c3 s/c slip at 14nm or 10.3ftlb,, its ok????

    Ya you should be OK with that..Your gonna want to pull it and recheck it after s few hours of run time and reset it if nessessary...

  9. #9
    GOT BOOST? Dockside's Avatar
    Join Date
    Dec 2008
    Location
    Ontario, Canada
    Posts
    3,879
    +1
    116
    Why are you running a C3 charger on a RXT-X 260?????

  10. #10
    abie_lah's Avatar
    Join Date
    Jul 2009
    Location
    Kuala Terengganu, Malaysia
    Posts
    264
    im running my rxt today with new s/c cluth at c3 set at 14nm slipping,,, get 8050rpm and 73mph with 15/20r solas and not a boost cut,,,very diffrent at mid top end compare with stock rxt260

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Another XSPOWER Intercooler Setup *Updated Results*
    By 1FastTrespiper in forum 4-Tec Performance
    Replies: 53
    Last Post: 04-23-2006, 09:16 PM
  2. UMI bar setup
    By brad2510 in forum 4-Tec Performance
    Replies: 5
    Last Post: 04-10-2006, 08:51 PM
  3. Lemoine NOPAS Setup RXP/RXT
    By mrracing in forum 4-Tec Performance
    Replies: 16
    Last Post: 12-06-2005, 06:14 PM
  4. What's the good pump setup for a stock 03 GTX-SC?
    By Jarrett in forum 4-Tec Performance
    Replies: 10
    Last Post: 07-15-2005, 05:17 AM
  5. Would this be an ok mod setup for a budget????
    By kenshin89 in forum 4-Tec Performance
    Replies: 13
    Last Post: 05-25-2005, 07:08 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •