Page 1 of 2 12 LastLast
Results 1 to 10 of 15
  1. #1
    Therock's Avatar
    Join Date
    Apr 2005
    Location
    Jacksonville,FL
    Posts
    170

    What are the current records of the fastest ski's??

    What are the current records of the fastest ski's??

    Also, Jerry where is the stock inter cooler located?? I see the picture of the inter cooler but I just cant seem to find it my boat.. Hopefully i'm not asking a stupid question. And i'm assuming you remove it if your installing one???????


  2. #2
    Site Admin Green Hulk's Avatar
    Join Date
    Apr 2005
    Location
    Morgan City, LA
    Posts
    34,995
    +1
    1,902
    The world record is 87.5 on a GPR.

    The stock intercooler is located in your intake manifold. Yes, you do have to remove it when installing the Rotax Racing external intercooler.

  3. #3

    Join Date
    Apr 2005
    Location
    Augusta GA
    Posts
    720
    I was almost beat the current worlds record. I got my RXP up to ....................85mph gpsed on I 95 south behind my truck LOL

  4. #4
    Therock's Avatar
    Join Date
    Apr 2005
    Location
    Jacksonville,FL
    Posts
    170
    Is it easy to remove?? I want to install my new intercooler. It looked like i needed to remove my bov tube and install the intercooler.

  5. #5
    mgo7483's Avatar
    Join Date
    May 2005
    Location
    Jacksonville, Florida
    Posts
    176
    You remove the stock intercooler buy removing the two water hoses, then remove the clamp which holds the intercooler in place, then you pull it out towards the front of the ski. I think you might have to loosen the fuel tank or something to get clearance to pull it out, but Jerry will tell you for sure.

  6. #6
    Site Admin Green Hulk's Avatar
    Join Date
    Apr 2005
    Location
    Morgan City, LA
    Posts
    34,995
    +1
    1,902
    Actually, you also have to unbolt the intake manifold. Very easy task as it's only 7 bolts. Once unbolted you just lift the intake manifold up and the stock intercooler will slide far enough forward for removal.

    If you have the Riva BOV you will need to remove it as the external intercooler has it's own plumbing fixtures that will take the place of where that BOV was located.

  7. #7
    Therock's Avatar
    Join Date
    Apr 2005
    Location
    Jacksonville,FL
    Posts
    170
    Do you have to put any type of sealant when you tighten down the manifold?

  8. #8
    Site Admin Green Hulk's Avatar
    Join Date
    Apr 2005
    Location
    Morgan City, LA
    Posts
    34,995
    +1
    1,902
    No, as you can see in this picture off of my main site there is an O ring seal around each of the ports.


  9. #9
    Therock's Avatar
    Join Date
    Apr 2005
    Location
    Jacksonville,FL
    Posts
    170
    The rubbers are the sealers?????????

  10. #10
    Site Admin Green Hulk's Avatar
    Join Date
    Apr 2005
    Location
    Morgan City, LA
    Posts
    34,995
    +1
    1,902
    yes, those orange things around the port are what seal it. No need for silicone sealant.

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. What are you currently using to log afr, boost,RPM, etc
    By DR2006RXP in forum 4-Tec Performance
    Replies: 53
    Last Post: 04-18-2013, 01:54 AM
  2. What are some good games for the PS3? Just picked one up..
    By caliburst in forum Open Discussion
    Replies: 41
    Last Post: 03-19-2009, 08:47 PM
  3. Replies: 26
    Last Post: 01-07-2009, 07:47 PM
  4. What are some simple mods for the 2008 Wake?
    By skyline99k in forum Sea Doo Open Discussion
    Replies: 10
    Last Post: 06-03-2008, 06:58 PM
  5. what are some good games for the xbox 360??
    By LiquidDI in forum Sea Doo Open Discussion
    Replies: 7
    Last Post: 03-10-2006, 01:17 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •