Results 1 to 9 of 9
  1. #1
    abie_lah's Avatar
    Join Date
    Jul 2009
    Location
    Kuala Terengganu, Malaysia
    Posts
    264

    Innovate Motorsport MTX

    can Innovate Motorsport MTX comunicate with vipec like lc1 inovatefor reading afr???


  2. #2

    Join Date
    Jul 2009
    Location
    FL
    Posts
    45
    +1
    2
    If it has an analog output it can. You can calibrate the ViPEC input assigned to it to read the correct afr's.

  3. #3
    abie_lah's Avatar
    Join Date
    Jul 2009
    Location
    Kuala Terengganu, Malaysia
    Posts
    264
    where i can get wiring diagram for install mtx or lc1 inovate to vipec ecu??

  4. #4

    Join Date
    Jul 2009
    Location
    FL
    Posts
    45
    +1
    2
    The ViPEC ecu has a Wideband Lambda input already on the harness (small grey 2 wire connector). Pin one is signal and pin two is switched 12v power. As far as the Innovate product I would reference their website under support. The manual for the product will list the wires and colors.

    You can contact me by email and I will get you the part number for the connector so you can make your own connections. The ViPEC calibration can then be changed or you can configure the Innovate's output to the ViPEC's calibration that is already setup.

  5. #5
    abie_lah's Avatar
    Join Date
    Jul 2009
    Location
    Kuala Terengganu, Malaysia
    Posts
    264
    im already connect a wire and afr reading have in vipec but vipec reading not same with mtx meter,, 12.5 at meter but 12.1 at vipec monitor,,im use an6 with cal5 setup,,, if use lc1 setup no reading at vipec,,,

  6. #6

    Join Date
    Jul 2009
    Location
    FL
    Posts
    45
    +1
    2
    Quote Originally Posted by abie_lah View Post
    im already connect a wire and afr reading have in vipec but vipec reading not same with mtx meter,, 12.5 at meter but 12.1 at vipec monitor,,im use an6 with cal5 setup,,, if use lc1 setup no reading at vipec,,,
    Contact me via email and I will help you with the cal table.

  7. #7
    abie_lah's Avatar
    Join Date
    Jul 2009
    Location
    Kuala Terengganu, Malaysia
    Posts
    264
    what is ur email???
    [email protected]
    its my email

  8. #8

    Join Date
    Jul 2009
    Location
    FL
    Posts
    45
    +1
    2
    Have you made the needed changes to the calibration yet?

  9. #9
    abie_lah's Avatar
    Join Date
    Jul 2009
    Location
    Kuala Terengganu, Malaysia
    Posts
    264
    not yet,, now im change a water line,, after this i can change it and give u a result,,,

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. SOLD Innovate Motorsports Digital MTX Series Air/Fuel Ratio Gauge
    By FZS Monty in forum Yamaha Classifieds
    Replies: 2
    Last Post: 04-04-2013, 05:47 PM
  2. Innovate Motorsport MTX
    By Trond in forum 4-Tec Performance
    Replies: 21
    Last Post: 01-28-2011, 10:08 AM
  3. FS Innovate Motorsports LM-2 AFR Meter
    By Tiburon1264 in forum Sea Doo Classifieds
    Replies: 18
    Last Post: 01-07-2010, 02:44 PM
  4. FS Innovate Motorsports HBX-1
    By vxrpete8 in forum Sea Doo Classifieds
    Replies: 6
    Last Post: 09-11-2009, 09:26 AM
  5. Innovate Motorsports.
    By beerdart in forum 4-Tec Performance
    Replies: 2
    Last Post: 01-30-2009, 11:57 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •