Page 1 of 2 1 2 LastLast
Results 1 to 10 of 12
  1. #1
    Water4fire's Avatar
    Join Date
    May 2005
    Location
    New Braunfels TX.
    Posts
    10,062
    +1
    790

    Teds Conversion drive shaft

    Guys I have a Teds drive shaft that was ordered for a 50mm seadoo adapter plate for a gprxp. BUT like a dumb behind I bought a 75mm adapter from philip as I did not do my home work correctly.

    So I am gonna sell my NEW Never used Teds driveshaft at a reduced rate to help someone out.

    I have spoke to Philip and he makes 50mm adapters so if someone wants to buy this and save money and then buy the adapter from Philipgpr just contact him and I.

    Also if you have a JD-1 adapter it is 50mm's also!

    Pic is bellow and all you get is the driveshaft in the pic. It was test fitted and found it was the short one and is still mint NEW!

    Anyway Mint new never run teds conversion drive shaft. $335 shipped to your door.


    Please just pm me for any questions or post here.


  2. #2
    Water4fire's Avatar
    Join Date
    May 2005
    Location
    New Braunfels TX.
    Posts
    10,062
    +1
    790
    Guys since I have ordered anothere shaft from Ted/Mark, I really don't just need this one sitting on the shelf as I will not ever switch my adapter size and use it. If you are building a conversion This is a super deal. So anyway to maybe make this easier to move, I will take parts on trade to help move this thing. I would ocnsider a XSCer, Stock X 42lb injecters and a Riva X Bar clamp. NOTE I don't want JUNK!

  3. #3
    HydroFool GPRSHO thomaswester's Avatar
    Join Date
    Sep 2009
    Location
    FINLAND (oravais)
    Posts
    487
    +1
    25
    Hello.
    Can I ask in what material is it made​​?
    Thank You
    Thomas Wester

  4. #4
    Water4fire's Avatar
    Join Date
    May 2005
    Location
    New Braunfels TX.
    Posts
    10,062
    +1
    790
    Thomas you may ask, but I will not be able to tell you as I really don't know the answer. I will say it is made by the best in the bussiness, PERIOD, (Ted Thompson)Ted is the one that fixes everyone elses crap, but you pay for it. If you don't know ted and is work it really is hard to understand, but In my opinion he is the one you can trust with out a doubt.
    I will ask him or mark to post if they can. YOU will not be dissappointed and YES I will ship it to you in FINLAND.

  5. #5
    HydroFool GPRSHO thomaswester's Avatar
    Join Date
    Sep 2009
    Location
    FINLAND (oravais)
    Posts
    487
    +1
    25
    Okey nice.
    I'm a little interested to build the seadoo pump on the gprxp.
    I'll be in touch in case I want to buy it.
    Thank you
    Thomas Wester

  6. #6
    Hydrotoys's Avatar
    Join Date
    Jul 2005
    Location
    Mesa, AZ
    Posts
    16,712
    +1
    85
    I'll let Ted answer if he wants to. Here is an email he sent the SD guys for their extension driveshafts that he is making...

    The material and heat-treat used would equate to 200,000 PSI of tensile strength, compared to the aftermarket shafts sent to me for evaluation is at around 110,000 PSI.......so ours would be almost double the strength. The Seadoo oem and after market shafts are made from low-cost carbon steels and induction hardened at the splines...this is why they rust away when left wet. I suspect the stock SD shafts are made from 4140 or 8620

    We would use a certified stainless and processes it in a completely heat-treated state to help minimize runout and distortion that will occur when post heat-treating. This stainless will be very close to what a SHO/FZR or GPR driveshaft are made from, so as you know, rust and corrosion would be greatly reduced along with superior strength advantage.

  7. #7
    Water4fire's Avatar
    Join Date
    May 2005
    Location
    New Braunfels TX.
    Posts
    10,062
    +1
    790
    Guys in order to help compensate some for the other drive shaft purchase I am gonna lower the price on this shaft. I am gonna go a full $100 off the new price and offer it at $325 shipped to your door in the US.
    I will ship anywhre for just actual shipping.
    Take the $100 Savings and buy the 50mm adapter from Philip and that is a hell of a deal IMO.

    Thanks

  8. #8
    Water4fire's Avatar
    Join Date
    May 2005
    Location
    New Braunfels TX.
    Posts
    10,062
    +1
    790
    Is anyone at all interested in this shaft?
    It is for the JD-1 ----50mm seadoo pump adapter for a gprxp conversion.

    You can also have philip make you a 50mm adapter.

    Not even a low ball offer????
    .

  9. #9
    Moderator Insanediego Joe's Avatar
    Join Date
    Mar 2006
    Location
    San Diego, California, United States
    Posts
    5,885
    +1
    142
    150.00 bucs plus shipping...Is that low enough?

  10. #10
    Water4fire's Avatar
    Join Date
    May 2005
    Location
    New Braunfels TX.
    Posts
    10,062
    +1
    790
    Sale Pending payment!

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Conversion drive shaft, motor mounts, exhaust hook up parts!
    By 2fast4u in forum Conversion PWC Performance Skis
    Replies: 1
    Last Post: 05-01-2015, 05:37 AM
  2. looking for GPRXP conversion drive shaft to buy
    By KyleP in forum Conversion PWC Performance Skis
    Replies: 4
    Last Post: 01-15-2012, 04:39 PM
  3. Teds Extended Drive Shaft Broke!
    By icerat4 in forum 4-Tec Performance
    Replies: 164
    Last Post: 12-19-2011, 10:51 AM
  4. FS conversion drive shaft for sale GPRXP
    By henn in forum Conversion Skis Classifieds
    Replies: 5
    Last Post: 08-15-2010, 07:39 PM
  5. WTB - Ted conversion drive shaft
    By mrbtd in forum Conversion Skis Classifieds
    Replies: 7
    Last Post: 07-21-2009, 08:15 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •