Page 1 of 4 1 2 3 ... LastLast
Results 1 to 10 of 33
  1. #1
    Kelly_A's Avatar
    Join Date
    Dec 2009
    Location
    Central Oklahoma
    Posts
    660
    +1
    17

    Parting out 2009 FZR SHO Motor (thrown rod)

    I'm parting out my 2009 FZS/FZR SHO motor that threw the #2 rod, venting the case.

    All parts available including sensors, complete head, intake, exhaust, throttle body, SC and crank. Engine has <40 hrs.

    Note that some of the externals are from a used, rebuilt, engine I purchased from Riva and may have some surface saltwater corrosion.

    Will also consider an offer for all, as a parts motor, if you can travel to central Oklahoma for pickup.

    Prices extremely reasonable, I need my garage back. Just send me a PM and let me know what you need.

    Update: Complete R&D Powershot (14 hours) FS - $160.00
    ___

    Update: Complete head, supercharger housing, oil pan and SC clutch have sold.

    Update: Rectifier has sold

    Update: Valve cover and Oil Pump have sold

    Update: Temp sensor has sold

    Update: Powershot has sold

    ___

    Update: All remaining parts have sold
    Last edited by Kelly_A; 06-28-2012 at 01:34 PM.


  2. #2
    crashhard's Avatar
    Join Date
    Jul 2007
    Location
    Philly PA, Wildwood NJ, Indialantic FL
    Posts
    2,382
    +1
    24
    Pm me a price on the head. Thanks

  3. #3
    shhr's Avatar
    Join Date
    May 2005
    Location
    Springfield,TN
    Posts
    2,546
    +1
    311
    what are you doing with the hull and stuff, if selling I am interested in the rear seat and bracket

  4. #4
    SHOBiz's Avatar
    Join Date
    Jul 2008
    Location
    Wylie, Texas
    Posts
    3,577
    Might be interested in the case (upper/lower) and oil pan for the right price
    Besides a hole any other damage to the case? Pics?

  5. #5
    Kelly_A's Avatar
    Join Date
    Dec 2009
    Location
    Central Oklahoma
    Posts
    660
    +1
    17
    Here's a pic of the engine. Refer to first post about which parts remain available.


  6. #6

    Join Date
    Sep 2007
    Location
    Littleton,NC on Lake Gaston
    Posts
    261
    +1
    23
    Quote Originally Posted by Kelly_A View Post
    Here's a pic of the engine. Refer to first post about which parts remain available.

    Kelly let me know if you are going to sell the reverse bucket,brackets,spring,bolts and sleeves. Hate to see a hole in your cases. Do you have any idea what caused this. Oldman

  7. #7
    Kelly_A's Avatar
    Join Date
    Dec 2009
    Location
    Central Oklahoma
    Posts
    660
    +1
    17
    I finished the rebuild last week - ski's running strong, 82+ on the GPS, and that's taking it easy during break in. I can only surmise it was a catastrophic failure of the #2 rod. Rebuilt motor has Riva/Carillo internals, so hopefully there won't be a repeat. None of the hull components are for sale, since they're all being used again. Sent the ECU off Monday for a R2 to R3 re-reflash, want to be able to take the powershot out of the equation. ECU is due back tomorrow, so I'll be back on the water this weekend.

  8. #8

    Join Date
    Sep 2007
    Location
    Littleton,NC on Lake Gaston
    Posts
    261
    +1
    23
    Kelly thanks for letting me know. Are you still running the low boost ET wheel. Going to put my fzr in next week with new R2 reflash low boost wheel. Glen told me that I should not need powershot but leaving it on Jet Ski unhooked just in case. Oldman

  9. #9
    Kelly_A's Avatar
    Join Date
    Dec 2009
    Location
    Central Oklahoma
    Posts
    660
    +1
    17
    Yes, same wheel. Needed Powershot at red 7-8 to keep AFR at 11.8 WOT on R2. Yellow and green 1 (off).
    Hopefully R3 will provide the added fuel for WOT. Unless there's been a change in the R2 map since last summer, you may well need the powershot.

  10. #10
    hi.i like to know if you have the supercharge yet and the price.

Page 1 of 4 1 2 3 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Anyone parting out a red sho 2008-2009?
    By [email protected] in forum Yamaha PWC Performance (4-stroke)
    Replies: 0
    Last Post: 07-19-2015, 06:31 PM
  2. suggestions on parting out 2009 FZR
    By JoeyDFZS in forum Yamaha Open Discussion
    Replies: 5
    Last Post: 03-06-2015, 10:58 AM
  3. WTB - Parts need an oil pump 2009 2010 fzr sho motor
    By Rocketman in forum Yamaha Classifieds
    Replies: 4
    Last Post: 09-08-2014, 01:52 PM
  4. FS parting out triple pipe 1200r motor
    By tealgreen2000 in forum Yamaha Classifieds
    Replies: 13
    Last Post: 11-26-2010, 12:00 AM
  5. FZR/SHO - Forged Pistons & Rods - Debate
    By Carlos Thomas in forum Yamaha PWC Performance (4-stroke)
    Replies: 16
    Last Post: 08-02-2009, 10:51 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •