Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11
  1. #1
    WATER WOODY's Avatar
    Join Date
    Aug 2005
    Location
    Minden, Nevada, United States
    Posts
    10,664
    +1
    11

    Lowell Horning hits another bullseye!

    This guy amazes me.I sent him my R&D heads a few months ago,gave him my target psi,got them back(fast),installed them,he hit my psi DEAD ON!!!!!! I had a water intrusion problem a short time back.I sent Lowell my #3 head for pressure test and had him drop compression to my target psi.Just got the head back,he hit it DEAD ON again! Remember,im at 4100' elevation. Lowell has years of experience with building sleds which generally run at higher altitudes,like mine.It just blows me away how accurate he is.

    Lowell,thanks again for ANOTHER super job! Glad you are getting back to great health.


  2. #2
    Moderator RX951's Avatar
    Join Date
    Apr 2005
    Location
    League City, Texas
    Posts
    16,066
    +1
    23
    Lowell is Da-Man

    Gald you got yur stuff back, I know your chompin at da bit to git in the water

  3. #3
    WATER WOODY's Avatar
    Join Date
    Aug 2005
    Location
    Minden, Nevada, United States
    Posts
    10,664
    +1
    11
    Quote Originally Posted by RX951 View Post
    Lowell is Da-Man

    Gald you got yur stuff back, I know your chompin at da bit to git in the water
    Going to the water tomarrow Billy.Its gunna be 23 degrees in the morning.I think ill leave a little later. Setting the EFI up a couple notches. I sure want to hit 74+ up here with stock nonported/non powervalve slugs.

    BTW Billy,i like your new signature! 75.6 sucka !!!!!!!!!!

  4. #4
    spud's Avatar
    Join Date
    Jul 2006
    Location
    Oceanside, California
    Posts
    1,347
    +1
    2
    I've had a lot of engine work done on quads in the past. Big name companies too. Lowell's work is superior to them. He is a stand up guy.

  5. #5
    mtrager's Avatar
    Join Date
    Jul 2006
    Location
    Orlando, Florida, United States
    Posts
    2,443
    +1
    2
    Setting the EFI up a couple notches.


    Woody,

    Warm it up and crank it up.

    Good luck.

  6. #6
    WATER WOODY's Avatar
    Join Date
    Aug 2005
    Location
    Minden, Nevada, United States
    Posts
    10,664
    +1
    11
    Quote Originally Posted by mtrager View Post
    Setting the EFI up a couple notches.


    Woody,

    Warm it up and crank it up.

    Good luck.
    Thanks Mark...will do Its gettin STABBED!!!!!!!!

  7. #7
    spud's Avatar
    Join Date
    Jul 2006
    Location
    Oceanside, California
    Posts
    1,347
    +1
    2
    Woody,

    I see you have a Banshee. Welcome to the Banshee owners club. Do you ever get to Glamis?

    Put the powervalved 500cc kit Trinity sells on it. Those things rock.

  8. #8
    WATER WOODY's Avatar
    Join Date
    Aug 2005
    Location
    Minden, Nevada, United States
    Posts
    10,664
    +1
    11
    Spud,how much hp and $$$$$?

  9. #9
    spud's Avatar
    Join Date
    Jul 2006
    Location
    Oceanside, California
    Posts
    1,347
    +1
    2
    www.trinityracing.com

    I havent looked it up yet. I think it was about 2500. The horsepower was way up there for a quad. They don't specify hp.

    Get that put it on alchohol and flat smoke everyone.

    What mods are on it now?

    I've got Toomeys, V-Force reeds, Vito's Key, Pro Design cool head pump gas, oversized radiator, Proflow air cleaner and boot. Skat 8 paddle haulers and a 4" over chromed swingarm. Its good for 80% of the quads racing up Oldsmobile hill. There are some exotic quads out there.

  10. #10
    WATER WOODY's Avatar
    Join Date
    Aug 2005
    Location
    Minden, Nevada, United States
    Posts
    10,664
    +1
    11
    Just got it 3 weeks ago

    LRD pipes
    filter/rejet
    some billet stuff

    Just got my .040 Vito piston kits.Getting a cool head,4 degree plate,porting,reeds,32mm carbs .60hp range is what im looking at.

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. FS...Used Reed Spacer purchased from Lowell Horning
    By need4pwr in forum Yamaha Classifieds
    Replies: 5
    Last Post: 07-28-2008, 12:36 PM
  2. Lowell Horning
    By eric1238 in forum Yamaha Open Discussion
    Replies: 11
    Last Post: 05-20-2008, 03:34 PM
  3. Lowell Horning.. Great Guy !!!!!!!
    By james k in forum Yamaha Open Discussion
    Replies: 11
    Last Post: 09-08-2007, 07:41 PM
  4. Need jetting specs 1300r lowell horning port
    By gpr-mike in forum Yamaha PWC Performance (2-stroke)
    Replies: 24
    Last Post: 06-06-2007, 05:38 PM
  5. Thanks to Lowell Horning
    By Mongoose in forum Yamaha PWC Performance (2-stroke)
    Replies: 1
    Last Post: 04-18-2006, 06:30 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •