Thread: No spark
05-04-2011, 12:38 PM #1
Hoi guys i have big problem maybe you can help me?
I had a oil pressure problem so i thought i solves it! I can ran the ski on the trailer and it run not nice because the code P0520 ( oil sensor ).
I went whit the ski to the wather so i destroyed not the carbonseal.
When i hit the startbutton the ski wont start anymore
The code P0339 came up!
So i went to the dealer to read the ski and the only code that came up was P0520.
I change that sensor but the rxp wont start i have no spark!!!
Please help someone from holland
05-05-2011, 10:57 PM #2
- Join Date
- May 2011
05-06-2011, 05:35 AM #3
Check your fuses, then load test your battery.
05-06-2011, 12:13 PM #4
I went back to the dealer and he hooked the computer again on my ski. Hy test the ecu and everything but works fine!
The only thing i could try he said is my camshaft sensor. The code p0339 was not there anymore but only i saw that code at home?
So i will try next week a new camshaft sensor ans hopefully he fired!!
If not then they and i wontnow it anymore.
05-14-2011, 08:08 AM #5
I changed the camshaft sensor. Still it wont start i have ony a spark at cilinder one. if i moves the coil to cilinder one and two it has no spark?
Could it be the crankshaft sensor and where is it located?
I have have checked the onm on pin A5 and A19 and that is 230ohm.
Does anybody now where to look now i dont now it
05-16-2011, 11:03 AM #6
05-16-2011, 08:19 PM #7
If u have spark at only 1 cyl , and not the other 2, then u have either 2 bad coil packs, 2 blown fuses,2 bad plugs, or broken wires to the coil packs.
Have u checked the fuses that run those coil packs in the MPEM?
Any friends with the same year ski, u could try swapping the ECU, and coil packs with?
05-16-2011, 09:01 PM #8
i had two bad coils on my setup. the only way i could tell was pulling each plug at idle. if yours isnt starting it may be possible to pull the plugs with coil attached and check for spark, keeping away from fuel tho.
05-17-2011, 04:35 AM #9
Yes i have checked the fuses they are good. I moved coil and plug from cilinder one to two and three? A i am going to check the groundwire and if not he is really dead!
05-17-2011, 06:26 AM #10
I have checked the wires with a meter that goes to the coil it has on all wires 10,1 volt!! I have checked all coils they have 0,15 ohm. Is this ok?
I think its good but still no spark. Good it be the crankshaft sensor because he is going to tell when to spark??
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
By chrishoward81 in forum Yamaha Old School SkisReplies: 1Last Post: 04-15-2011, 09:23 PM
By lubemaster in forum Polaris How To & FAQsReplies: 6Last Post: 08-17-2010, 09:55 PM
By Discokaj in forum Yamaha PWC Performance (2-stroke)Replies: 0Last Post: 07-29-2010, 03:08 PM
By bullwinkle in forum 2-Stroke PerformanceReplies: 1Last Post: 07-09-2009, 08:16 PM
By Kraf-T in forum 2-Stroke PerformanceReplies: 3Last Post: 03-29-2009, 03:17 PM