Results 1 to 8 of 8

Thread: just checking

  1. #1
    WFO 4 LIFE nitrosportman's Avatar
    Join Date
    May 2011
    Location
    Temple, TX
    Posts
    235

    just checking

    1996 polaris slx780 bore should be 71.3 mm correct ?
    i ordered .5mm oversize

    that would mean i need to go to 71.8mm is this correct ?

    just wanted to make sure i have the correct dimensions before it start honing it out you know measure twice cut once

    almost here
    http://www.fedex.com/Tracking?trackn...ttype=ivother&


  2. #2
    WFO 4 LIFE nitrosportman's Avatar
    Join Date
    May 2011
    Location
    Temple, TX
    Posts
    235
    muahahahaha these things are pretty

    and disregard the question im good now

  3. #3
    She likes the bike. But the ski gets her wet!!!! xlint89's Avatar
    Join Date
    Oct 2006
    Location
    Cleveland OH
    Posts
    17,330
    +1
    31
    Are you planning to hone almost .5mm?

  4. #4
    WFO 4 LIFE nitrosportman's Avatar
    Join Date
    May 2011
    Location
    Temple, TX
    Posts
    235
    yup i've done bigger just got to measure alot

  5. #5
    She likes the bike. But the ski gets her wet!!!! xlint89's Avatar
    Join Date
    Oct 2006
    Location
    Cleveland OH
    Posts
    17,330
    +1
    31
    That's alot of honing.....


    Obviously you aren't afraid of "out of round"?

  6. #6
    WFO 4 LIFE nitrosportman's Avatar
    Join Date
    May 2011
    Location
    Temple, TX
    Posts
    235
    yeah a little ill do a rough cut up with 220 stones to within a few thousandths then follow it up with a 400 grit it should be fine hopefully it will be fine

  7. #7
    She likes the bike. But the ski gets her wet!!!! xlint89's Avatar
    Join Date
    Oct 2006
    Location
    Cleveland OH
    Posts
    17,330
    +1
    31
    Ok, good luck.

  8. #8
    WFO 4 LIFE nitrosportman's Avatar
    Join Date
    May 2011
    Location
    Temple, TX
    Posts
    235
    thanks patience is not one of my strong points honestly i would have rather went with a smaller piston but i couldn't find one at the time now i have a place to get standard pistons

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Just checked compression, new rings and or pistons needed??
    By gordo1287 in forum Polaris Open Discussion
    Replies: 36
    Last Post: 02-22-2013, 12:02 AM
  2. FS S3 Charger, 22 Hours, Slip just checked, Riva Washers. 250 SHIPPED
    By Mtuned in forum Sea Doo Classifieds
    Replies: 7
    Last Post: 11-03-2011, 12:29 PM
  3. New to PWC's just got 98 GP800, what should I check.
    By ChewyR in forum Yamaha PWC Performance (2-stroke)
    Replies: 4
    Last Post: 01-12-2008, 06:57 PM
  4. 94 SL 750 just purchased what should i check?
    By GameDemon in forum Polaris Open Discussion
    Replies: 5
    Last Post: 06-19-2007, 12:01 AM
  5. Just checked super charger slip
    By Top banana in forum 4-Tec Performance
    Replies: 11
    Last Post: 08-09-2006, 01:24 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •