Results 1 to 5 of 5
  1. #1
    jetskier90's Avatar
    Join Date
    Jun 2007
    Location
    Vashon, WA
    Posts
    78

    Waveraider impeller housing??

    I've been trying to replace the impeller on my '94 raider 701 with a new Solas. My wear ring is binding due to corrosion.
    Also I can not get the stock impeller off the shaft, I've tried everything- torch, water, oil, impact gun, hammer, etc.

    Does anyone have a driveshaft and housing WITHOUT the impeller they would be willing to sell me? What's in the picture but no impeller.

    If your around Seattle/Puget Sound i can come pickup or just use paypal if you're not local.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	Screen shot 2011-06-05 at 4.57.29 PM.png 
Views:	117 
Size:	379.6 KB 
ID:	241213  


  2. #2
    Old Ski Insanity w/rpm500's Avatar
    Join Date
    Aug 2005
    Location
    Crystal River Fl
    Posts
    2,208
    your best bet is ebay ...look for 144mm pumps .. they came in raiders w/701's and the gp's w /760s ..
    and if you dont have a spline holder get one...
    as your looking at the pump pictured, impeller rotation to come off ,is up... threads are left handed (which ever way the blade leading edge faces is the way to turn it )

  3. #3
    jetskier90's Avatar
    Join Date
    Jun 2007
    Location
    Vashon, WA
    Posts
    78
    I've been checking ebay, so far no luck, issue seems to be I want one without the impeller. I do have the spline tool and am turning it the correct way, reverse thread.

  4. #4
    Old Ski Insanity w/rpm500's Avatar
    Join Date
    Aug 2005
    Location
    Crystal River Fl
    Posts
    2,208
    weld that spline tool to a 3 or 4 foot log section of thick angle iron..you can stand on it then.. your impeller will have to be heated at the hub just behind the nut drive area.. I file'd large wrench to fit the yamaha drive size ( those ends arnt perfectly hex) .. lay it down with someone standing on both ends or park the car on the channel opposite the rotation, with a 2x4 spacer on it,heat and shock it off the shaft with a good solid heavy hammer strike to the wrench...(hasnt failed for me yet)... you, if heavy enough could just give it (the wrench)a good stomp with a heavy boot..

  5. #5
    Old Ski Insanity w/rpm500's Avatar
    Join Date
    Aug 2005
    Location
    Crystal River Fl
    Posts
    2,208
    not to sound an ass...(just making sure)
    you are holding the spline stationary and turning the hubs drive Up?..
    ( as your picture is situated here, it is 'UP' to loosen ,wrench nearest to you..)

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. how do i install an impeller housing on a waveraider
    By brando785 in forum Yamaha Old School Skis
    Replies: 3
    Last Post: 07-15-2015, 10:02 PM
  2. Bad impeller housing...
    By OutlawGPR in forum Yamaha PWC Performance (2-stroke)
    Replies: 6
    Last Post: 01-15-2007, 10:05 AM
  3. Clearance on impeller/housing.....
    By OutlawGPR in forum Yamaha PWC Performance (2-stroke)
    Replies: 2
    Last Post: 01-13-2007, 09:51 PM
  4. Replies: 2
    Last Post: 12-12-2006, 10:13 PM
  5. Impeller housing...Plastic
    By Troy Hammond in forum Yamaha PWC Performance (2-stroke)
    Replies: 1
    Last Post: 07-08-2006, 02:05 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •