Results 1 to 8 of 8
  1. #1
    Roll Tide!! SeadooTech's Avatar
    Join Date
    Jun 2011
    Location
    Birmingham, AL
    Posts
    662
    +1
    18

    05 guts in a 06RXP

    I purchased a 05 RXP with broken cam chain and the hull is in terrible shape. I know where a pristine 2006 RXP hull is that has been gutted. Would everything from the 2005 work in the 2006. LIke the gauge, I know if i used all the electronics and engine that it would work. Just wasn't 100% sure if there would be any problems... thanks


  2. #2
    mrbtd's Avatar
    Join Date
    Jul 2005
    Location
    Lindenhurst, Illinois, United States
    Posts
    4,309
    +1
    2
    Yes.. the cutout for the gauge is slightly different. Just have to drill a couple holes.

  3. #3
    Roll Tide!! SeadooTech's Avatar
    Join Date
    Jun 2011
    Location
    Birmingham, AL
    Posts
    662
    +1
    18
    ok thanks, but everything else will bolt up right.... how close is the shape of the two clusters. Is it alot of work, what about the vts. does it go through the gauge then to the vts, if im using the older gauge with new vts.... just making sure before i buy the new hull and have more problems than I want... I can clean the 05 hull up but will take some work... thanks

  4. #4
    Roll Tide!! SeadooTech's Avatar
    Join Date
    Jun 2011
    Location
    Birmingham, AL
    Posts
    662
    +1
    18
    I there any way to make the 06 gauge work with the 05 harness

  5. #5
    Roll Tide!! SeadooTech's Avatar
    Join Date
    Jun 2011
    Location
    Birmingham, AL
    Posts
    662
    +1
    18
    ok, the 05 has like 7 wires and the 06 has 4 wires. what do the clusters do differently for the other 3 Wires

  6. #6
    mrbtd's Avatar
    Join Date
    Jul 2005
    Location
    Lindenhurst, Illinois, United States
    Posts
    4,309
    +1
    2
    No the gauges wont swap.

  7. #7
    Quote Originally Posted by SeadooTech View Post
    ok, the 05 has like 7 wires and the 06 has 4 wires. what do the clusters do differently for the other 3 Wires
    The gauge in the 05 communicates with the MPEM for all the info. The gauges for 06+ switched to a direct CAN communication from the ECU. You cannot mix them.

  8. #8
    Roll Tide!! SeadooTech's Avatar
    Join Date
    Jun 2011
    Location
    Birmingham, AL
    Posts
    662
    +1
    18
    Even If i used the 06 wiring harness(which I have one), most of the sensors should be the same, or would the crank position change the game... I do know back in 07 I had to install a 05 motor(not knowing the different CPS locations) in a 07 boat, so i cut the plugs off the CPS and soldered the 07 lead on the 05 motor and it worked... I'm a master cert. tech but never tried swapping stuff out.. I always order the correct parts but this is my personal boat...

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Need Help - '05 Rxp In Trouble
    By jwade in forum 4-Tec Performance
    Replies: 16
    Last Post: 08-18-2008, 08:08 AM
  2. Advice or help inspecting a used 05 RXT in Pomona, CA?
    By GTI-SE4426 in forum Sea Doo Classifieds
    Replies: 4
    Last Post: 07-25-2008, 07:37 PM
  3. Advice or help inspecting a used 05 RXT in Pomona, CA?
    By GTI-SE4426 in forum Sea Doo Open Discussion
    Replies: 4
    Last Post: 07-25-2008, 07:36 PM
  4. water in hull 06rxp?
    By csam in forum Sea Doo Open Discussion
    Replies: 3
    Last Post: 06-18-2008, 05:06 PM
  5. 05 RXP In Shop for 3 months
    By SpeedStang95 in forum 4-Tec Performance
    Replies: 10
    Last Post: 10-12-2005, 12:20 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •