Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11
  1. #1

    Join Date
    Feb 2006
    Location
    Birmingham AL
    Posts
    2,924
    +1
    2


  2. #2
    Fastest in my cove sfackett0's Avatar
    Join Date
    Aug 2007
    Location
    Sparrows Point, MD (near the Key Bridge)
    Posts
    1,000
    +1
    22
    I wouldnt, not worth the risky just to save $30

  3. #3
    Moderator Snoman's Avatar
    Join Date
    Apr 2006
    Location
    South Chicagoland
    Posts
    14,688
    +1
    846
    Quote Originally Posted by sfackett0 View Post
    I wouldnt, not worth the risky just to save $30
    +1..if you do not know were they are coming from then i would definaly stay away from them..

  4. #4
    Booner76's Avatar
    Join Date
    Oct 2009
    Location
    Stirling ,Ont.
    Posts
    222
    +1
    5
    Quote Originally Posted by Snoman View Post
    +1..if you do not know were they are coming from then i would definaly stay away from them..
    +1... Fer sure! Would never skimp on an intrical part as SC washers.

  5. #5
    ou812's Avatar
    Join Date
    Jun 2006
    Location
    Riverside,ca
    Posts
    6,210
    +1
    198
    I'd be Cautious, but then again GH/riva had to be trusted when they came out with their washers at 1st...
    This seller has feedback on the washers, ask him about the failure rate. Maybe they are just as good as riva's? I mean, riva isn't the only one able to make these ya know & we all know riva's prices are usually higher than we like. I'm sure someone on here has bought a set...
    I'm not sure if this is the same seller or not but I grabbed a set of "No Name Washers" about 3 or 4 years ago for my RXP on riva S3 wheel, XS IC, etc. & if I recall correctly they survived over 50hrs of ocean & river riding before my Riva ceramic bearings went.

    LOL, give it a shot & let us know...

  6. #6
    mikelytle1077's Avatar
    Join Date
    Sep 2010
    Location
    frisco, tx
    Posts
    955
    +1
    37
    i have a set in my gtx with a gen2 wheel been over 10hrs no problems, checked slip at 5hrs no difference. i have a set of rivas in my rxp and the rivas were lighter dont know if that makes a difference. imo the rivas are a bit overpriced, the hydrostream ebay ones seemed like top notch tool grade metal just my observation. ps im always off and on the throttle a lot of abuse on the gtx.

  7. #7
    ou812's Avatar
    Join Date
    Jun 2006
    Location
    Riverside,ca
    Posts
    6,210
    +1
    198
    Quote Originally Posted by mikelytle1077 View Post
    i have a set in my gtx with a gen2 wheel been over 10hrs no problems, checked slip at 5hrs no difference. i have a set of rivas in my rxp and the rivas were lighter dont know if that makes a difference. imo the rivas are a bit overpriced, the hydrostream ebay ones seemed like top notch tool grade metal just my observation. ps im always off and on the throttle a lot of abuse on the gtx.
    There's a place to start keeping tabs on these washers... Keep us posted mike..

  8. #8
    mikelytle1077's Avatar
    Join Date
    Sep 2010
    Location
    frisco, tx
    Posts
    955
    +1
    37
    im on it they should be fine

  9. #9

    Join Date
    Apr 2008
    Location
    kennewick WA
    Posts
    111
    TTT I was thinking about buying their kit for a stock 04 rxp with all the tools for $119.95. Yea everyone swears by riva and for good reason, I just think it is worth bringing this back up to see if anyone has tried them since this post started a year ago. My rxp is just used for giving my 5 yr old a ride so her mom and I can switch back and forth on her sxr stand up. We gave up the couches and switched to stand ups. The rxp has 169 hours and still has ceramic washers.

  10. #10
    I have once, I wanted to try un coated washers, I've noticed some gaulling on the coated ones. But never got to check as the ski was confiscated a month after I did it, it did have over twenty hours up without breaking if that's any thing to go by.

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Anyone ever seen these?
    By Dark_viper42 in forum Sea Doo Open Discussion
    Replies: 5
    Last Post: 05-27-2007, 07:00 PM
  2. Keel gaurd, anyone ever use
    By Rodneyae in forum Polaris Open Discussion
    Replies: 11
    Last Post: 02-22-2007, 11:38 PM
  3. Anyone ever use this?
    By ADAMBOMB in forum Sea Doo Open Discussion
    Replies: 1
    Last Post: 04-21-2006, 07:36 PM
  4. Has anyone ever used their fire extinguisher?
    By Pistonwash in forum Yamaha Open Discussion
    Replies: 18
    Last Post: 03-04-2006, 11:30 AM
  5. PWC DEPTHFINDERS (ANYONE EVER USED ONE??)
    By ABBOTT in forum Yamaha How To & FAQs
    Replies: 17
    Last Post: 02-01-2006, 08:48 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •