Page 1 of 2 1 2 LastLast
Results 1 to 10 of 19
  1. #1
    Rendog's Avatar
    Join Date
    May 2005
    Location
    jacksonville fl.
    Posts
    1,282
    +1
    2

    Need direction on a engine code!

    P-1202 is the engine code. Im getting itermittent warnings then the engine goes into limp mode! Unplug the lanyard and it resets and rides great for any amount of time!Any advice where to find the oil pressure switch so that I can start troubleshooting is much appreciated!


  2. #2
    Rendog's Avatar
    Join Date
    May 2005
    Location
    jacksonville fl.
    Posts
    1,282
    +1
    2
    Ok, I did some searching and found some info on the switches. i found the one at the rear, any idea on the one @ the front? Any one with some experience and advice on this problem?

  3. #3

    Join Date
    Jun 2005
    Location
    rome ga
    Posts
    938
    +1
    20
    The one in the rear under throttle body is oil pressure. It will read oil in the window when it is happening. The one in the front is crankcase pressure and fails quite often in 04 models. You can un plug it and the ski will run. It senses crankcase pressure after riding awhile. Do you hear the tops valve open after inserting the Lanyard?

  4. #4

    Join Date
    Jun 2005
    Location
    rome ga
    Posts
    938
    +1
    20
    You can take the guts out of the tops valve to be sure the crankcase is breathing. Probably bad switch.

  5. #5
    Rendog's Avatar
    Join Date
    May 2005
    Location
    jacksonville fl.
    Posts
    1,282
    +1
    2
    Give me an idea of what the TOP valve sounds like. And where is the one up front located?

  6. #6

    Join Date
    Jun 2005
    Location
    rome ga
    Posts
    938
    +1
    20
    It is a relay it clicks when you insert key.

  7. #7
    Rendog's Avatar
    Join Date
    May 2005
    Location
    jacksonville fl.
    Posts
    1,282
    +1
    2
    I dont hear a clicking sound after inserting lanyard, only a fuel pump!

  8. #8

    Join Date
    Jun 2005
    Location
    rome ga
    Posts
    938
    +1
    20
    You can ohm the front sensor it should read 0 ohm.

  9. #9

    Join Date
    Jun 2005
    Location
    rome ga
    Posts
    938
    +1
    20
    The front oil switch is only $25 might wanna change it.

  10. #10
    Rendog's Avatar
    Join Date
    May 2005
    Location
    jacksonville fl.
    Posts
    1,282
    +1
    2
    Ok , will do, thanks bro!

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Replies: 9
    Last Post: 07-12-2013, 09:14 PM
  2. what gaskets need sealer on 94 sl750 polaris fuji engine
    By ultradoc in forum Polaris Projects
    Replies: 3
    Last Post: 10-16-2010, 08:26 PM
  3. stainless braided hoses, need direction on install
    By jetmanjay in forum 4-Tec Performance
    Replies: 8
    Last Post: 08-30-2010, 03:00 AM
  4. Need Help on RXP Engine in Ohio
    By LeeMajors12 in forum 4-Tec Performance
    Replies: 2
    Last Post: 07-24-2008, 02:29 PM
  5. Need advice on engine repair, please help!
    By iolaus in forum 4-Tec Performance
    Replies: 41
    Last Post: 07-16-2008, 10:31 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •