Page 1 of 2 1 2 LastLast
Results 1 to 10 of 13
  1. #1
    ultra300x 702's Avatar
    Join Date
    Nov 2011
    Location
    Las Vegas NV
    Posts
    266
    +1
    6

    300x Cruise Control Removal for Aftermarket Throttle lever

    Cruise Control Unit Removal- Trace the wire harness coming up from the bottom loom and removed the front acess panel where the ecu is located. Tug on both ends to ensure you are unplugging the correct harness. Its plugged into this gray connector pictured below.






  2. #2
    ultra300x 702's Avatar
    Join Date
    Nov 2011
    Location
    Las Vegas NV
    Posts
    266
    +1
    6
    thanks sirbreaksalot I like your setup looks clean. Did you drill a notch in your bars for the little nub on the cruise unit or was the bar pre drilled or did you file it down etc?

  3. #3
    ultra300x 702's Avatar
    Join Date
    Nov 2011
    Location
    Las Vegas NV
    Posts
    266
    +1
    6
    DId you modify your front piece and cut off a portion? Look how big mine is below


  4. #4
    ultra300x 702's Avatar
    Join Date
    Nov 2011
    Location
    Las Vegas NV
    Posts
    266
    +1
    6
    my bars dont allow enough space for both. The tbm throttle lever design is very tight clearance with the odi grip. The ski is mostly used for racing anyway so i dont think i will miss my cruise or wake mode =)

  5. #5
    Banned User
    Join Date
    Jan 2009
    Location
    LA/oc
    Posts
    3,911
    +1
    129
    Quote Originally Posted by ultra300x 702 View Post
    my bars dont allow enough space for both. The tbm throttle lever design is very tight clearance with the odi grip. The ski is mostly used for racing anyway so i dont think i will miss my cruise or wake mode =)
    I ran both Tbm and blowison there's room no prob for it to all fit.

  6. #6
    ultra300x 702's Avatar
    Join Date
    Nov 2011
    Location
    Las Vegas NV
    Posts
    266
    +1
    6
    Thanks FIRE. ODI grips have a metal end piece the TBM lever rubs against it. I guess i could try and make it work but its very tight. Did you drill a notch in your bars or file down the nub for the cruise unit?

  7. #7
    Banned User
    Join Date
    Jan 2009
    Location
    LA/oc
    Posts
    3,911
    +1
    129
    Quote Originally Posted by ultra300x 702 View Post
    Thanks FIRE. ODI grips have a metal end piece the TBM lever rubs against it. I guess i could try and make it work but its very tight. Did you drill a notch in your bars or file down the nub for the cruise unit?
    I have ODI grips as well. Just file the nub off. And clearance the inside of the case a little bit. It should all fit no prob. The Tbm lever actuall gives you more room since its smaller.

  8. #8
    ultra300x 702's Avatar
    Join Date
    Nov 2011
    Location
    Las Vegas NV
    Posts
    266
    +1
    6
    Sh!t, my runabout bars dont have the room must be the bend comapared to your star bars. I put everything as close as i could and the bend in the bars starts is right where i need to clamp it down i got the first 2 screws strarted and notch already drilled. This is a fucked now i got a hole in my bar and it wont clamp down lol. Any ideas

  9. #9
    ultra300x 702's Avatar
    Join Date
    Nov 2011
    Location
    Las Vegas NV
    Posts
    266
    +1
    6
    If you look below this is all the room i have in between the unit before the bend starts and it wont clamp shut.

    Quote Originally Posted by ultra300x 702 View Post
    DId you modify your front piece and cut off a portion? Look how big mine is below


  10. #10
    Banned User
    Join Date
    Jan 2009
    Location
    LA/oc
    Posts
    3,911
    +1
    129
    I just used a multi bit and drilled out the inside or a dreamel works also like waz said. U just need to clearance the inside of the case.

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Aftermarket Throttle Lever
    By Ericruiz911 in forum Yamaha PWC Performance (4-stroke)
    Replies: 1
    Last Post: 02-19-2016, 10:23 AM
  2. Ultra 300x Cruise control when using SLO key
    By Dozza in forum Kawasaki How To & FAQs
    Replies: 0
    Last Post: 10-30-2014, 01:21 AM
  3. SOLD Looking for a Throttle lever
    By Plut in forum Polaris Skis
    Replies: 2
    Last Post: 03-09-2014, 05:53 PM
  4. Aftermarket cruise control or throttle lock for 2011 STX-15F?
    By mghurle in forum Kawasaki PWC Performance (4-stroke)
    Replies: 1
    Last Post: 06-25-2012, 10:16 AM
  5. WTB: Throttle lever for 95 SL
    By Larsonator in forum Polaris Classifieds
    Replies: 7
    Last Post: 06-20-2008, 03:36 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •