Thread: Want to see 80MPH on my RXP
01-12-2007, 11:18 AM #1
Want to see 80MPH on my RXP
My 06 RXP has the Riva Stage 1, Free flow with Ride Plate holes filled ect.
My best has been 72 @ 8050RPM
What would be the best mods to start the climb to 80.
I am considering the Riva SC, ECU and Injectors to start. WHat kind of gains should I get with these additions?
I have seen the all the parts list for the Riva Stage 3 but want to build as my pocket can afford.
01-12-2007, 11:23 AM #2
You will see 79-80 on a good day with the mods you mentioned, but you will also need to get the Riva lightweight valvetrain to run the higher RPM's and an intercooler. Without the intercooler you would be way too rich. If you only have money for one then you need to start with the intercooler and get the ECU later.
If you want a solid 80 mph all day long dig deep into your pocket.
You will need:
either Riva ECU with 50# injectors or
Rotax Racing ECU with 50# injectors and fuel controller
(RR ECU will give you better performance with the Rude Charger)
Riva Pro series intercooler
Riva lightweight valvetrain
Thru hull exhaust
Riva rear air intake kit
01-12-2007, 11:25 AM #3
The Riva Stage 3 SHOULD get you to 80. The RR ECU/b kit/fuel controller/50# injector set up (with lightened valvetrain) WILL get you to 80+.
01-12-2007, 11:26 AM #4
- Join Date
- Jun 2005
- rome ga
The stage 3 is made to work together. The sc will help the most but requires more fuel. If you just add bigger injectors you have starting and idle problems. So buy these 3 together would be my advice. For a cheaper get buy the 10lb rr sc wheel is a good bang for $500.
01-12-2007, 02:04 PM #5
- Join Date
- Feb 2006
- Birmingham AL
Yank the motor and put it in a GPR
01-12-2007, 03:00 PM #6
Send me $1,000.00 and I will tell you how to do it...
01-12-2007, 11:24 PM #7For a cheaper get buy the 10lb rr sc wheel is a good bang for $500.
01-12-2007, 11:26 PM #8
hey Charles where the hell u been bro?
01-13-2007, 01:09 PM #9
01-13-2007, 11:15 PM #10
Jerry my internet has been down for 2 weeks! mxl16, I had basically a stage 2 setup with RR ECU and sc wheel.... It took a b kit , 4" air intake, nozzle kit, and alittle cool wheather to get the 82+....
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
By great lakes gpr 1200 in forum Yamaha Open DiscussionReplies: 12Last Post: 03-27-2008, 05:16 PM
By shawn alladio in forum High Performance Watercraft SafetyReplies: 0Last Post: 03-14-2008, 05:43 AM
By Raider Kevin in forum Yamaha Open DiscussionReplies: 106Last Post: 03-13-2008, 02:36 PM
By ADAMBOMB in forum SoutheastReplies: 4Last Post: 05-03-2007, 01:49 AM
By idizzy in forum Yamaha Open DiscussionReplies: 15Last Post: 03-13-2006, 01:04 AM