Results 1 to 7 of 7
  1. #1
    skigolfnut's Avatar
    Join Date
    Jun 2009
    Location
    League City TX
    Posts
    1,979
    +1
    33

    How to get dipstick tube out 06 rxp??

    I need to get my dipstick tube out of my rxp any easy way?


  2. #2
    skigolfnut's Avatar
    Join Date
    Jun 2009
    Location
    League City TX
    Posts
    1,979
    +1
    33
    I just saw an old post to loosen the mani bolts and tilt it to get the tube out,

  3. #3
    Moderator Snoman's Avatar
    Join Date
    Apr 2006
    Location
    South Chicagoland
    Posts
    14,688
    +1
    846
    Quote Originally Posted by skigolfnut View Post
    I just saw an old post to loosen the mani bolts and tilt it to get the tube out,
    Correct..you need to loose the intake manny and pull the dipstick off of it...it slides into a little groove on the manny...

  4. #4
    skigolfnut's Avatar
    Join Date
    Jun 2009
    Location
    League City TX
    Posts
    1,979
    +1
    33
    Almost a disaster, I noticed my oil a little above the line so I was going to suck a little oil out, and had my brothers pump bulb siphon,
    I pulled out about a 1/2 quart of oil and when I went to pull the hose out the last little bit of hose broke off into the dipstick tube, I could see it just to the top,
    I just removed the dip stick tube and pushed the hose out with the dipstick, it was all there,
    I guess the hose had got brittle from being used in gasoline,

  5. #5
    This is how I run a jetski shop in the desert nmpeter's Avatar
    Join Date
    May 2008
    Location
    Elephant Butte New Mexico
    Posts
    6,529
    +1
    1,278
    I ran into that issue last season with my oil extractor tube getting brittle from using it on hot oil. Now I buy a new set each season. As Beerdart mentioned, removing the manifold bolts allows extraction of the dipstick tube. Not as painful as my panicked reaction first led me to believe

  6. #6
    i got one in my 07 rxp that broke off, pulled the manny off and dip tube housing to find nothing. What need to be done next? motor out? or just leave it in there?

  7. #7
    Ski Hacks MG's Avatar
    Join Date
    Apr 2013
    Location
    Georgia
    Posts
    5,253
    +1
    990
    Pull motor, split cases and remove plastic tubing.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. how to get good performance out of a 94 slt 750
    By lmidden in forum Polaris PWC Performance
    Replies: 30
    Last Post: 12-08-2013, 12:17 AM
  2. Replies: 5
    Last Post: 02-18-2012, 06:46 PM
  3. How to get the water out?
    By X-Runner in forum Polaris Open Discussion
    Replies: 14
    Last Post: 03-13-2011, 05:06 AM
  4. How to remove body panel on 06 RXP
    By Slick PWC in forum Sea Doo Open Discussion
    Replies: 6
    Last Post: 11-09-2010, 05:58 PM
  5. what is the best way to get hot air out of rxp?
    By WICKEDSEADOO in forum 4-Tec Performance
    Replies: 7
    Last Post: 11-22-2009, 08:48 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •