Results 1 to 9 of 9
  1. #1
    PuprleNuprleGPR's Avatar
    Join Date
    Jul 2006
    Location
    Central FL
    Posts
    741

    2004 GP1300R - needs work

    The ski is a 2004 with ~125 hours.

    SOLD! Thanks to all who showed interest.

    The stinger mount4 on the cylinder is in need of repair. The bolt hole needs to be welded, redrilled, and tapped - buying a new cylinder or running a smaller stinger pipe is the other solution. This is the problem that has kept the ski out of commission for almost 6 years. The only mods that will come on the ski are a Riva D-Plate and Jetworks plumbing [need new $2 rubber detent in the JW valve]. A competent mechanic should be able to get it on the water with minimal expense.

    I am finally trying to make room for a Superjet, so this one needs to go. It does not come with a trailer and it is located in Lake Mary, FL - just 20 minutes North East4 of Orlando.

    I can get better and more specific photos upon request.

    Click image for larger version. 

Name:	dsc1153x.jpg 
Views:	58 
Size:	38.3 KB 
ID:	272714
    Click image for larger version. 

Name:	dsc1154u.jpg 
Views:	64 
Size:	35.1 KB 
ID:	272715
    Click image for larger version. 

Name:	dsc1152h.jpg 
Views:	84 
Size:	131.3 KB 
ID:	272716
    Click image for larger version. 

Name:	dsc1151j.jpg 
Views:	75 
Size:	313.8 KB 
ID:	272717
    Picture of the damage
    Click image for larger version. 

Name:	pic1vi.jpg 
Views:	117 
Size:	80.7 KB 
ID:	272713

    Thanks for looking.
    Last edited by PuprleNuprleGPR; 06-08-2012 at 07:18 PM.


  2. #2
    PuprleNuprleGPR's Avatar
    Join Date
    Jul 2006
    Location
    Central FL
    Posts
    741
    bump
    Last edited by PuprleNuprleGPR; 06-05-2012 at 10:58 AM.

  3. #3

  4. #4
    Happily Self-Employed WFO's Avatar
    Join Date
    Nov 2005
    Location
    Houston, Texas
    Posts
    12,801
    +1
    450
    you have a single trailer available to go with the ski?

  5. #5
    PuprleNuprleGPR's Avatar
    Join Date
    Jul 2006
    Location
    Central FL
    Posts
    741
    No Rich, I do not. If I did, it would already be on its way to Alabama

  6. #6

    Join Date
    Feb 2006
    Location
    Birmingham AL
    Posts
    2,924
    +1
    2

  7. #7

    Join Date
    Mar 2012
    Location
    Pensacola Florida
    Posts
    39
    Are there any runability issues whatsoever with this ski other than the broken bolt? When was the last time the engine was run? What is the compression in each cylinder? Do you have the oem stock exhaust?

  8. #8
    PuprleNuprleGPR's Avatar
    Join Date
    Jul 2006
    Location
    Central FL
    Posts
    741
    Yes, I have all of the OEM parts, including new exhaust mount brackets and studs.

    The was last run 6 years ago and it ran fine. Compression was tested at ~110 a week ago, BUT keep in mind that the gas is likely mush, the rings were relatively dry [only had 2 oz oil to drip between the 3 cylinders], and I was using a 20 yr old SnapOn gauge. I believe that the important thing is that they are all even and that they should regain compression with a bit of run time.

    Let me know if you have any further questions.

  9. #9
    PuprleNuprleGPR's Avatar
    Join Date
    Jul 2006
    Location
    Central FL
    Posts
    741
    SOLD! Thanks to all who showed interest.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Need some help with 2004 GP1300R bogging down
    By JohnnyLSousa in forum Yamaha PWC Performance (2-stroke)
    Replies: 7
    Last Post: 09-15-2015, 11:21 AM
  2. SOLD 2004 SeaDoo RXP - Needs Work
    By boudin in forum Sea Doo 4Tec Skis
    Replies: 3
    Last Post: 07-05-2013, 06:51 PM
  3. FS - Parts : RXP HULL - (2004) Clear/Clean Title (Hull Needs Work)
    By BartenderSmalley in forum Sea Doo Classifieds
    Replies: 2
    Last Post: 01-29-2012, 12:15 PM
  4. 2004 GP1300R waveeater clips (are they needed?)
    By mylspen in forum Yamaha PWC Performance (2-stroke)
    Replies: 6
    Last Post: 08-31-2010, 08:08 PM
  5. Fuel pump in gp1300r not working?
    By wildman326 in forum Yamaha PWC Performance (2-stroke)
    Replies: 2
    Last Post: 05-20-2006, 08:54 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •