Results 1 to 10 of 20
Thread: 1200 Engine
-
06-06-2012, 08:06 PM #1
- Join Date
- Sep 2006
- Posts
- 1,060
- +1
- 1
1200 Engine
I have a spare 1200 from the '00 Genesis I parted out a few months ago. Compression checks out at (M-C-P) 124-125-122. The bore on the MAG had some slight vertical scoring on the intake side. By the numbers, it doesn't appear to be affecting compression, but I want to make sure any buyer knows it's there. I didn't see anything on the PTO. You could probably do a hone and rering and get the compression up to the other two. (I'd probably just run it like it is if I were using it.)
This is from a fuel injected machine so you'll have to tap the pulse fittings if you use it on a carb'd ski. There are directions somewhere here on the site. It's pretty easy.
I am selling the the stripped block/jugs only - no intake, exhaust, mag housing, starter, or anything else. I need to keep it as light and small as possible.
Asking $700 + shipping from TX.
PM me as I don't check classifieds every day because the new forum layout.Last edited by bgaidan; 08-25-2012 at 07:31 PM.
-
06-07-2012, 09:06 PM #2
- Join Date
- Sep 2006
- Posts
- 1,060
- +1
- 1
Pitcherz:
Compression - MAG to PTO:
"Wash" (I know this doesn't mean as much on a DI, but it shows you it was running properly.)
-
06-11-2012, 07:07 PM #3
- Join Date
- Sep 2006
- Posts
- 1,060
- +1
- 1
Bump before it goes to ebay!
-
06-11-2012, 08:24 PM #4Preserving the Polaris classics
- Join Date
- Jun 2010
- Location
- Milwaukee WI
- Posts
- 7,094
- +1
- 190
Come on guys......Great deal!!!!!!!!
-
06-13-2012, 11:00 AM #5Yup! made in USA
- Join Date
- May 2010
- Location
- Tampa, FL
- Posts
- 537
- +1
- 3
Surprise noone jumps on this ... so much talk about going big
Free bump
-
07-08-2012, 05:35 PM #6drwebb
- Join Date
- May 2007
- Location
- okla
- Posts
- 170
genesis
where at in tx ?
Originally Posted by loonatik
Surprise noone jumps on this ... so much talk about going big
Free bump
-
07-08-2012, 05:50 PM #7
- Join Date
- Sep 2006
- Posts
- 1,060
- +1
- 1
DFW
-
07-08-2012, 06:01 PM #8
- Join Date
- Feb 2010
- Location
- Port Lambton, Ontario
- Posts
- 36
If you want to part the motor...I would be interested in the best cylinder piston set.....i'll pm you on the slth stuff when I get back from my kids hockey
-
07-08-2012, 06:15 PM #9
- Join Date
- Sep 2006
- Posts
- 1,060
- +1
- 1
No going to part this one. I know it'll sell if I put it in Ebay....just been too busy lately.
Edit: I already have a box that'll be perfect for it if I do have to ship it!
-
07-12-2012, 11:41 AM #10
- Join Date
- May 2011
- Posts
- 4
Just found out motor blown on my 02 Virage TXI- assume this engine would fit? Sorry not motor guy, would have to have mechanic do
Reply With QuoteThread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
