Page 1 of 4 1 2 3 ... LastLast
Results 1 to 10 of 35
  1. #1

    300X SPSE after R&D module install ????

    hi everyone !! last tuesday I got my R&D ride plate intake and module install after go for a ride after 5 minute the ski was running idle in the water without code or anything and then I went full throttle for about 1000 feet get 72 mph on gps and the rpm went back down to 7500 at 66 mph and the FI code came on and after pressing mode and set at the same time I got an SPSE code can you guys help please thanks!!!


  2. #2
    nicjak's Avatar
    Join Date
    Mar 2008
    Location
    Warragul, Downunder
    Posts
    7,794
    +1
    625
    your scom module wire has come out of the ecu connector

  3. #3
    Banned User
    Join Date
    Jan 2009
    Location
    LA/oc
    Posts
    3,911
    +1
    129
    Quote Originally Posted by nicjak View Post
    your scom module wire has come out of the ecu connector
    X2........

  4. #4
    I check all that already and its all good . I took off my scom module and still have the same code,and now I wonder what we have to do with the brown and white wire that I have to took out to put the blue one in ? can I broke somethin without hookin that brown and white wire ? thanks for your help!!!

  5. #5
    nicjak's Avatar
    Join Date
    Mar 2008
    Location
    Warragul, Downunder
    Posts
    7,794
    +1
    625
    you need the wire connected to clear the code you have either broke the wire connector or its simply not pushed in far enough (this will be your problem) look at the reverse side of the plug and take notice of the wire position, then make sure it is fully inserted like the rest (you should be able to see the female shiny pin on the edge of the connector like the rest).

  6. #6
    Banned User
    Join Date
    Jan 2009
    Location
    LA/oc
    Posts
    3,911
    +1
    129
    Just a note to the Above if it does not clear after reconnecting go spin the paddle wheel by hand as the ski needs to register the signal.

  7. #7
    I just went back to have a look and my connector are all good , I unhook the batterie and still have the code come on what you did with the white and brown wire?

  8. #8
    Banned User
    Join Date
    Jan 2009
    Location
    LA/oc
    Posts
    3,911
    +1
    129
    Quote Originally Posted by maxmerc9 View Post
    I just went back to have a look and my connector are all good , I unhook the batterie and still have the code come on what you did with the white and brown wire?
    Wait. U pull the brown wire out replace it with the white one from the scom unhooking the batteries won't clear the code u need to spin the paddle wheel If it's all hooked up correctly is it even hooked up ?

  9. #9
    yeah its all hook up correctly and I spin the wheel as fast as I can and still have the code

  10. #10
    nicjak's Avatar
    Join Date
    Mar 2008
    Location
    Warragul, Downunder
    Posts
    7,794
    +1
    625
    im as confused as you tommy!! are you sure the pin is fully inserted? (how can you tell)?

Page 1 of 4 1 2 3 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Ski Module Installed But Not Working on 2012 GTI SE 130!!
    By mmiller2197 in forum 4-Tec Performance
    Replies: 3
    Last Post: 03-19-2017, 06:14 PM
  2. Adjust your timing on your 300X skis with the Dynojet Ignition Module
    By Green Hulk in forum Kawasaki PWC Performance (4-stroke)
    Replies: 11
    Last Post: 04-11-2013, 03:49 PM
  3. 300x vibration after speed run
    By toomanytoys in forum Kawasaki PWC Performance (4-stroke)
    Replies: 19
    Last Post: 01-06-2013, 04:04 PM
  4. How to improve speed accuracy after R&D Ride Plate installed on 2012 Ultra 300X?
    By Vincent in forum Kawasaki PWC Performance (4-stroke)
    Replies: 51
    Last Post: 07-30-2012, 04:35 AM
  5. Macsboost module install question.
    By cdes in forum Honda Performance
    Replies: 4
    Last Post: 08-03-2011, 07:01 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •