Page 1 of 2 1 2 LastLast
Results 1 to 10 of 18
  1. #1
    Water4fire's Avatar
    Join Date
    May 2005
    Location
    New Braunfels TX.
    Posts
    10,065
    +1
    790

    Thru hull exaust templet

    Can anybody post measurements for the thru hull riva exaust outlet as i do not have the templet or send me the PDF for the templet.


  2. #2
    which ski, your RXP???
    you have PM...PR...

  3. #3
    Water4fire's Avatar
    Join Date
    May 2005
    Location
    New Braunfels TX.
    Posts
    10,065
    +1
    790
    yep its for the rxp

  4. #4
    here ya go, if this doesn`t come thru I can e-mail it to ya!...PR...

    When you print this make sure your Page scaling is set to NONE, that`s what mine is with the HP printer...
    You can print Riva`s directions and check template against that also!...
    Last edited by Pale Rider; 02-25-2007 at 11:51 AM.

  5. #5
    Water4fire's Avatar
    Join Date
    May 2005
    Location
    New Braunfels TX.
    Posts
    10,065
    +1
    790
    I just realized it is a RR exhaust!
    Will this matter?



    I finally have to do it as the 4in rear intake will not go past the power pipe.



    .


    .

  6. #6
    daverxp4's Avatar
    Join Date
    Aug 2005
    Location
    montreal,canada
    Posts
    1,323
    yes it does as i have installed one the exit is different then riva
    there is no template you must mesure

  7. #7
    Quote Originally Posted by Water4fire View Post
    I just realized it is a RR exhaust!
    Will this matter?



    I finally have to do it as the 4in rear intake will not go past the power pipe.



    .


    .
    Yes, the Rotax, Rude outlet is a dif height, I think it`s lower than the Riva ...PR...

  8. #8
    daverxp4's Avatar
    Join Date
    Aug 2005
    Location
    montreal,canada
    Posts
    1,323
    if i recall its actually higher then the riva

  9. #9
    Dont judge me...
    Join Date
    Jul 2006
    Location
    FLORIDA
    Posts
    610
    riva is lower

  10. #10
    Got Boost? psycho rxp's Avatar
    Join Date
    Jul 2005
    Location
    Port St. Lucie, FL
    Posts
    5,445
    +1
    182

    USING A HOLE SAW DRILL A 2 ¾" HOLE USING POINT "A" AS THE CENTER.POINT . MARK POINT "A" DRAWING A STRAIGHT LINE PARALLEL WITH LEFT SIDE OF HOOK THEN MEASURE DOWN LINE 65MM FROM EDGE OF HOOK WASHER.
    INSERT BILLET OUTLET INTO HOLE AND USE AS A TEMPLATE TO DRILL THE 4 MOUNTING HOLES. USE ¼ INCH DRILL BIT.
    INSTALL BILLET OUTLET USING A QUALITY SILICONE SUCH AS LOCTITE ULTRA BLACK OR EQUIVILENT.
    ALLOW SILICONE TO DRY BEFORE PUTTING PWC IN WATER TO CHECK FOR LEAKS.
    ENJOY THE SOUND AND PERFORMANCE.

    RACE TECH
    1992 VANDORF SIDEROAD
    AURORA, ON
    L4G 7B9
    905 726 3387

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Thru hull exaust help
    By benarm in forum 4-Tec Performance
    Replies: 5
    Last Post: 07-17-2011, 02:33 AM
  2. thru hull exaust
    By Avion3333 in forum 4-Tec Performance
    Replies: 20
    Last Post: 01-20-2009, 12:30 AM
  3. thru hull exaust
    By jeremy in forum 4-Tec Performance
    Replies: 0
    Last Post: 03-02-2006, 07:41 AM
  4. thru hull exaust
    By jeremy in forum 4-Tec Performance
    Replies: 9
    Last Post: 02-28-2006, 07:46 AM
  5. Riva's Thru hull exhaust!
    By Compwhiz82 in forum 4-Tec Performance
    Replies: 21
    Last Post: 06-25-2005, 11:08 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •