Results 1 to 6 of 6
  1. #1
    is thinking. grantuk's Avatar
    Join Date
    Sep 2006
    Location
    Surrey, UK
    Posts
    745
    +1
    19

    Superjet start/stop/lanyard on XPL?

    Hi again,

    I have. Franco remapped MPEM which allows any key to start the ski (I think as long as the connection is bridged it will start).

    I'd like to use a Yamaha Superjet start/stop/lanyard housing and wire it into the MPEM plug, this would mean I could use a normal Yamaha lanyard.

    Has anyone done this? Will it work?

    Thanks


  2. #2
    is thinking. grantuk's Avatar
    Join Date
    Sep 2006
    Location
    Surrey, UK
    Posts
    745
    +1
    19
    Anyone?

  3. #3
    kecheme's Avatar
    Join Date
    Jul 2011
    Location
    Phoenix Az
    Posts
    208
    +1
    7
    It will work. Cant recall what the yamaha kill switch does when pulled. Open circuit or closed. I did this years ago. I had to keep the dess working on my ski. I just used the yami to start/stop.

  4. #4
    is thinking. grantuk's Avatar
    Join Date
    Sep 2006
    Location
    Surrey, UK
    Posts
    745
    +1
    19
    Thanks, What do you mean you had to keep the DESS working, were you abel to replace the Sea-doo lanyard with the yammi one?

  5. #5
    kecheme's Avatar
    Join Date
    Jul 2011
    Location
    Phoenix Az
    Posts
    208
    +1
    7
    I first wired the the yamaha green start switch into the factory seadoo start/stop harness. Then kept the dess working like normal. This is the safest way.

    Later on I was able to rewire and use the yamaha key. The down side was every time the ski would sit I needed to remove and reattach the dess key.

    I dont remember the colors of what wires. But the green switch sent power to the starter relay and the red/key switch was wired to start/stop on seadoo.
    And VERY important when you wire in the green switch to the starter relay snip the factory ones so the MPEM can not actavate the relay.
    The factory seadoo has a single switch that doubles as a start/stop.

  6. #6
    kecheme's Avatar
    Join Date
    Jul 2011
    Location
    Phoenix Az
    Posts
    208
    +1
    7
    Overall the yamaha switch setup sucks when used in conjuction with Dess. You still have to reset the key after sitting.

    But it works nice when your rocking MSD total loss and simple wiring.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Sticky start/stop button on 03 gtx 4-tec
    By wags75 in forum Midwest
    Replies: 0
    Last Post: 07-26-2014, 10:53 AM
  2. looking for a broken start/stop/lanyard switch
    By markreef10 in forum Yamaha PWC Performance (2-stroke)
    Replies: 1
    Last Post: 05-27-2012, 05:54 PM
  3. How do you bypass LR-503 start/stop switch on a 2002 Virage i
    By mammalhead in forum Polaris How To & FAQs
    Replies: 0
    Last Post: 06-07-2011, 01:42 PM
  4. WTB start/stop lanyard
    By turk0004 in forum Polaris Classifieds
    Replies: 6
    Last Post: 10-18-2009, 11:04 PM
  5. Start/Stop circuit on Genesis test
    By VegasRatt in forum Polaris Open Discussion
    Replies: 12
    Last Post: 01-07-2008, 01:03 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •