Page 1 of 2 1 2 LastLast
Results 1 to 10 of 18
  1. #1
    prostocker's Avatar
    Join Date
    Oct 2012
    Location
    FL
    Posts
    442
    +1
    17

    Prostocker FZR 09 build 2012

    This is when i first got it and didn't want to do any mods.

    -Started with the intake grate and pump seal kit since i was removing the intake grate why not.
    -Then speed is addicted and i added the Riva Air Intake and ribbon delete.
    -But that was the worse mistake ever because i just wake up the monsters inside me for more speed decided to buy a rear exhaust because the sound and more power.
    -The riva water box was expensive and i decided to cut my OEM waterbox and empty inside and then weld back in.


  2. #2
    prostocker's Avatar
    Join Date
    Oct 2012
    Location
    FL
    Posts
    442
    +1
    17
    Watebox ready to be weld back togetherAttachment 286928
    -I was docking one day and got the temperature light then decided to do the engine cooling kit for reliability.
    -Added the HKS Blow Off valve to protect clutch and because it sounds great.
    That's when i got addicted to start ordering parts to make it faster little by little.
    Ordered Anti cavitation Cone
    Then R3 reflash repitch stock impeller and was doing 8120rpms
    want it to change the look of the fzr and started painting some plastics.
    Attachment 286929Attachment 286930Attachment 286931
    one of the speed runs in the ocean Attachment 286932

  3. #3
    prostocker's Avatar
    Join Date
    Oct 2012
    Location
    FL
    Posts
    442
    +1
    17
    Last update i ordered the Fizzle intercooler, i need to check rpms now to repitch impeller to archive my setup of 8500rpms with stock supercharger wheel and will post speed run pictures.Attachment 286933Attachment 286934

  4. #4
    r33pwrd's Avatar
    Join Date
    Mar 2006
    Location
    Sammamish Washington
    Posts
    4,216
    +1
    360

    Prostocker FZR 09 build 2012

    Looks good! Bet she is loud

  5. #5
    THE PLATE MAN JIM'S PERFORMANCE's Avatar
    Join Date
    Nov 2005
    Posts
    6,194
    +1
    535
    Hello prostocker, bad choice of cutting the outlet tube that short in the water box it will be getting full of water before it can get out. That's why the factory has it down low so it does not retain all that water.


  6. #6
    prostocker's Avatar
    Join Date
    Oct 2012
    Location
    FL
    Posts
    442
    +1
    17
    Quote Originally Posted by r33pwrd View Post
    Looks good! Bet she is loud
    Thank you, it's not too loud.
    Quote Originally Posted by JIM'S PERFORMANCE View Post
    Hello prostocker, bad choice of cutting the outlet tube that short in the water box it will be getting full of water before it can get out. That's why the factory has it down low so it does not retain all that water.
    So i cut it too short will it do any harm, like loose speed ? kill my hole shot ?

  7. #7
    THE PLATE MAN JIM'S PERFORMANCE's Avatar
    Join Date
    Nov 2005
    Posts
    6,194
    +1
    535
    Quote Originally Posted by prostocker View Post
    Quote Originally Posted by r33pwrd View Post
    Looks good! Bet she is loud
    Thank you, it's not too loud.
    Quote Originally Posted by JIM'S PERFORMANCE View Post
    Hello prostocker, bad choice of cutting the outlet tube that short in the water box it will be getting full of water before it can get out. That's why the factory has it down low so it does not retain all that water.
    So i cut it too short will it do any harm, like loose speed ? kill my hole shot ?
    It will kill your hole shot, and if you stop real fast it will even push water up the manifold into your exhaust valve.

  8. +1 by:


  9. #8
    prostocker's Avatar
    Join Date
    Oct 2012
    Location
    FL
    Posts
    442
    +1
    17
    Quote Originally Posted by JIM'S PERFORMANCE View Post
    Quote Originally Posted by prostocker View Post
    Quote Originally Posted by r33pwrd View Post
    Looks good! Bet she is loud
    Thank you, it's not too loud.
    Quote Originally Posted by JIM'S PERFORMANCE View Post
    Hello prostocker, bad choice of cutting the outlet tube that short in the water box it will be getting full of water before it can get out. That's why the factory has it down low so it does not retain all that water.
    So i cut it too short will it do any harm, like loose speed ? kill my hole shot ?
    It will kill your hole shot, and if you stop real fast it will even push water up the manifold into your exhaust valve.
    Ok thank you jim i will try to solder a extended tube inside the exit tube like it was from factory so water doesn't get in the exhaust valves.

  10. #9
    prostocker's Avatar
    Join Date
    Oct 2012
    Location
    FL
    Posts
    442
    +1
    17
    Just replace the outlet tube for bigger diameter 3.5 inches (opening) stock was like a little less than 3 inches, and extended all the way to the bottom of the waterbox like factory maybe the bigger diameter of 3.5 inches in opening gives me a little more power lol. big thanks to jim for letting me know about the problem.
    Attachment 287046Attachment 287047
    Last edited by prostocker; 11-12-2012 at 07:54 PM.

  11. #10
    AWA MEMBER
    Join Date
    Jan 2008
    Location
    Currituck, North Carolina, United States
    Posts
    4,616
    +1
    247
    Quote Originally Posted by prostocker View Post
    Last update i ordered the Fizzle intercooler, i need to check rpms now to repitch impeller to archive my setup of 8500rpms with stock supercharger wheel and will post speed run pictures.Attachment 286933Attachment 286934


    Im guessing 75.2mph

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Start Problem FZR 09
    By Lezzosoap in forum Yamaha PWC Performance (4-stroke)
    Replies: 5
    Last Post: 11-15-2012, 05:08 PM
  2. Problem with ECU FZR 09
    By prostocker in forum Yamaha PWC Performance (4-stroke)
    Replies: 13
    Last Post: 11-04-2012, 04:23 PM
  3. problem with an FZR 09'
    By waseemyah in forum Yamaha PWC Performance (4-stroke)
    Replies: 32
    Last Post: 05-02-2012, 02:07 PM
  4. vibration at 3k-4k with E1 in FZR 09'
    By waseemyah in forum Yamaha PWC Performance (4-stroke)
    Replies: 81
    Last Post: 04-01-2012, 01:54 PM
  5. yamaha fzr 09
    By srxp in forum Yamaha PWC Performance (4-stroke)
    Replies: 0
    Last Post: 05-23-2009, 04:11 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •