Page 1 of 2 1 2 LastLast
Results 1 to 10 of 12

Thread: VTS on RXT

  1. #1
    eb87's Avatar
    Join Date
    May 2010
    Location
    South East Coast
    Posts
    566
    +1
    25

    VTS on RXT

    I am trying to add VTS to my 05 RXT but looks like the module would sit at an angle causing the rod end to point down (as in the fiberglass over the pump is almost flush with the hole needed to be drilled in the plastic housing) There are no holes being drilled until I verify it fits. Can someone post pictures of what this area looks like with and without the VTS module? or am I being retarded and fits just fine after drilling the hole? Thanks


  2. #2
    jpeconsult's Avatar
    Join Date
    Jul 2007
    Location
    Pineville, LA
    Posts
    5,448
    +1
    1
    Browse the how-to's...Gus had written something about it.

  3. #3
    ou812's Avatar
    Join Date
    Jun 2006
    Location
    Riverside,ca
    Posts
    6,210
    +1
    198
    Use the Yamaha QSTS system. I did it to my 07 RXT and loved it.. No motors, nothing but a cable running through the back.. There's a sealed boss you drill out on the pump support where the trim "would" go..

    http://www.greenhulk.net/forums/show...=1#post1657037

  4. #4
    eb87's Avatar
    Join Date
    May 2010
    Location
    South East Coast
    Posts
    566
    +1
    25
    That looks great but I already added the needed wiring and have the vts motor, I just need to know how the motor fits cause it doesn't look like it will. I have seen the post in the how to but the pics don't show how it fits. Thanks.

  5. #5
    imp0ster's Avatar
    Join Date
    Dec 2011
    Location
    Palm Harbor, FL
    Posts
    5,037
    +1
    672
    Quote Originally Posted by eb87 View Post
    That looks great but I already added the needed wiring and have the vts motor, I just need to know how the motor fits cause it doesn't look like it will. I have seen the post in the how to but the pics don't show how it fits. Thanks.

    curious as to why you'd want to add that in an already very tight engine bay? I like the way the RXT runs with the pump wedge.

  6. #6
    krouchchocolate's Avatar
    Join Date
    Nov 2009
    Location
    Houston, TX
    Posts
    1,224
    +1
    53
    Quote Originally Posted by eb87 View Post
    That looks great but I already added the needed wiring and have the vts motor, I just need to know how the motor fits cause it doesn't look like it will. I have seen the post in the how to but the pics don't show how it fits. Thanks.
    I installed VTS in my 2006 RXT. It will fit for sure. I wired all the wires into my MPEM and then activated the VTS through the candoo system.

  7. #7
    jpeconsult's Avatar
    Join Date
    Jul 2007
    Location
    Pineville, LA
    Posts
    5,448
    +1
    1

    VTS on RXT

    Its on my GTX as well. It has been done several times before and I think it does set a tad bit skewed from vertical if I remember correctly.

  8. #8
    mac_man_luke's Avatar
    Join Date
    Sep 2010
    Location
    South Australia
    Posts
    1,262
    +1
    22
    I put VTS in my GTX, best upgrade ever.

  9. #9
    ou812's Avatar
    Join Date
    Jun 2006
    Location
    Riverside,ca
    Posts
    6,210
    +1
    198
    I ran with a 5.5 gal fuel cell in front. When it's full the rxt is nose heavy, trim it up till it's empty then trim back accordingly..

    [QUOTE=imp0ster;2090637]
    Quote Originally Posted by eb87 View Post
    curious as to why you'd want to add that in an already very tight engine bay? I like the way the RXT runs with the pump wedge.

  10. #10
    eb87's Avatar
    Join Date
    May 2010
    Location
    South East Coast
    Posts
    566
    +1
    25
    Quote Originally Posted by jpeconsult View Post
    Its on my GTX as well. It has been done several times before and I think it does set a tad bit skewed from vertical if I remember correctly.
    Yours it's an 05? how "skewd" is it? would you be so kind and take a few pics of the inside and outside? I just want to make sure before I start drilling holes on my ski. Many thanks.

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. vts on rxt
    By skidoochris in forum 4-Tec Performance
    Replies: 3
    Last Post: 10-29-2012, 07:52 PM
  2. VTS on RXT-X
    By clouless in forum 4-Tec Performance
    Replies: 7
    Last Post: 01-14-2009, 04:46 PM
  3. VTS on RXT
    By agibbs in forum 4-Tec Performance
    Replies: 11
    Last Post: 01-08-2008, 08:53 PM
  4. what wires for vts gauge on rxt
    By hydrojunkie in forum 4-Tec Performance
    Replies: 2
    Last Post: 09-01-2007, 01:59 PM
  5. VTS on Rxt??
    By MoTeC_Master in forum 4-Tec Performance
    Replies: 3
    Last Post: 08-19-2007, 03:18 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •