Results 1 to 3 of 3
  1. #1

    My 00 ZXI 1100 Project

    Hey guys,

    Just a few shots of my project, Very basic rebuild. I utilized WSM pistons @.50 over to retain future bores, Bore clearences for .50 were super close but managed to get it in spec. Tops are ceramic coated, head was milled conservative .005 to just get it flat and true, Deck was slivered .002 flat. Ports were smoothed and excess casting was eliminated exhaust polished marginally to eliminate casting, Motor was recolored to a "zombie brain" scheme to celebrate all you zombie's, drive was powdered and cleared with a dynafly 12/24 solas (Not sure how it will perform yet but it was only 36.00 brand new, setback slightly again very conservative) Objective was to
    retain stock performance but have reliability, Other mods were again simple, lightened flywheel, new seals, new stator, Oil pump eliminated (I run a 43:1 klotz technoplate pre-mix) and as a side note Keep a heads up on the stocker fuel filters, I think a majority of my previous lean condition was caused by a faulty OEM seam weld that caused a insanely slight air leak, I caught it purely by accident when I was warming up my workshop from about 30 to 70 degrees and just happen to be on the phone looking down, and I saw the seam of the filter just weeping a bit, when I applied several lbs of pressure (2) it all became evident it was most likely sucking air at the top under high RPMs causing a lean condition. I have a spare pump and will opt for dual cooling at a later date once that pump is rebuilt as a spare. I would like a second impeller more in the lines of stock for pulling tubes and such but open to suggestions. Also feedback on the DF 12/24 would be appreciated.

    See you in the summer
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	IMG_20121102_145840.jpg 
Views:	153 
Size:	98.1 KB 
ID:	290701   Click image for larger version. 

Name:	IMG_20121114_155436.jpg 
Views:	95 
Size:	77.7 KB 
ID:	290702   Click image for larger version. 

Name:	IMG_20121209_173731.jpg 
Views:	202 
Size:	69.3 KB 
ID:	290703   Click image for larger version. 

Name:	IMG_20121212_230526.jpg 
Views:	87 
Size:	32.3 KB 
ID:	290704   Click image for larger version. 

Name:	IMG_20121214_034049.jpg 
Views:	412 
Size:	72.4 KB 
ID:	290705  

  2. #2
    porschemaniac's Avatar
    Join Date
    Apr 2009
    Nice looking build! Great attention to detail

  3. #3
    My name is Sean and I am addicted to STXs smokeysevin's Avatar
    Join Date
    May 2008
    I like it a lot, it reminds me of a standup that another member built. I will try to dig it up.


Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 00 zxi 1100 won't go over 7 mph or over 4k rpm
    By 2000ws6transam in forum Kawasaki PWC Performance (2-stroke)
    Replies: 1
    Last Post: 07-24-2016, 10:46 PM
  2. how do i hook up my gas lines on my 99 zxi 1100
    By yodirt80 in forum Kawasaki How To & FAQs
    Replies: 1
    Last Post: 06-21-2011, 10:27 PM
  3. 2001 zxi 1100 roasted my first cylinder
    By offroadinjersey in forum Kawasaki PWC Performance (2-stroke)
    Replies: 11
    Last Post: 06-24-2009, 04:07 AM
  4. low compression on my 2001 ZXI 1100
    By offroadinjersey in forum Kawasaki PWC Performance (2-stroke)
    Replies: 3
    Last Post: 05-10-2009, 01:08 PM
  5. repair manual for my 1998 zxi 1100
    By jared427 in forum Kawasaki Open Discussion
    Replies: 3
    Last Post: 07-04-2008, 10:53 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts