Results 1 to 5 of 5
  1. #1
    Steve STSPERFORMANCE's Avatar
    Join Date
    Dec 2007
    Location
    Cambridge, Ohio
    Posts
    2,701
    +1
    116

    Motec diy m130 harness upgrade

    Got this done with the help of evan and nils thanks a ton guys! Figured i would post a how too as it was fairly simple. Evan was nervous about doing it but i calmed him down.

    -first i made a printout of the large and small connectors. Put a checkmark by all the ones already in use.
    -if you look at the back of the connector the pins are numbered. Transfer these numbers to your sheets
    -push up on small white piece on the bottom of the connector. There are two of them on the top side they will come up when you do. This allows you to insert new wires and pins.
    -dont worry about existing wires falling out when you do this there are locked in there either way.
    -nills made me up pins with 2 feet of wire attached too each. Pop up the small rubber plugs with a small screwdriver
    -do one row at a time. Put the color of the wire u are inserting into each hole on your sheet
    -push each pin all the way in you will feel them click when they seat
    -after you do a row of them go back and mark each wire with location. Example connectors are "a" and "b" i called them large and small. So if i put a wire in the small connector in number 6 hole i
    called it "s6"
    -take your time going row by row labeling as you go
    -once you are done with a connector look at it from the front make sure all pins are pushed in. Push down on the two white tabs this time. They will click back locking pins into place.
    -clean up the loom and gather all new wire in one spot
    -i filled all the open pins even though i wont need them. But now its easy say i want to moniter egt on cylinder 1 i would connect the egt sensor to an open wire, note the wire number and open up
    egt section of motec and tell it what pin its on. Easy easy!!
    -use connectors you can pull apart here so if you ever need too remove harness you can. Refer to you sheet when hooking up to confirm wire color. Im gonn try and find a male/female 20pin
    connector just like motec uses so i can make assemble/ dissassemble easy. nils can make you up the wire if ya need them!
    .Click image for larger version. 

Name:	2013-02-23_17-33-25_931.jpg 
Views:	84 
Size:	35.5 KB 
ID:	293478Click image for larger version. 

Name:	2013-02-23_17-37-48_604.jpg 
Views:	73 
Size:	29.2 KB 
ID:	293479Click image for larger version. 

Name:	2013-02-23_17-44-09_278.jpg 
Views:	272 
Size:	79.8 KB 
ID:	293480


  2. #2
    Steve STSPERFORMANCE's Avatar
    Join Date
    Dec 2007
    Location
    Cambridge, Ohio
    Posts
    2,701
    +1
    116
    Click image for larger version. 

Name:	2013-02-23_17-45-48_668.jpg 
Views:	63 
Size:	37.2 KB 
ID:	293481Click image for larger version. 

Name:	2013-02-23_17-46-56_463.jpg 
Views:	76 
Size:	46.0 KB 
ID:	293482Click image for larger version. 

Name:	2013-02-23_17-53-56_473.jpg 
Views:	75 
Size:	45.0 KB 
ID:	293483

  3. #3
    Steve STSPERFORMANCE's Avatar
    Join Date
    Dec 2007
    Location
    Cambridge, Ohio
    Posts
    2,701
    +1
    116
    Click image for larger version. 

Name:	2013-02-24_08-43-24_975.jpg 
Views:	75 
Size:	66.5 KB 
ID:	293484Click image for larger version. 

Name:	2013-02-24_09-13-18_45.jpg 
Views:	56 
Size:	45.9 KB 
ID:	293485Click image for larger version. 

Name:	IMG_20130224_084511.jpg 
Views:	57 
Size:	50.3 KB 
ID:	293486

  4. #4
    Steve STSPERFORMANCE's Avatar
    Join Date
    Dec 2007
    Location
    Cambridge, Ohio
    Posts
    2,701
    +1
    116
    Click image for larger version. 

Name:	2013-02-24_10-30-15_737.jpg 
Views:	78 
Size:	77.8 KB 
ID:	293488

  5. #5

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. FS - Parts Motec M130 harness
    By seadoo02xp in forum Sea Doo Classifieds
    Replies: 0
    Last Post: 01-24-2016, 05:44 PM
  2. FS Motec M400 with harness for 2010 and up I control
    By Bruce in forum Sea Doo Classifieds
    Replies: 1
    Last Post: 06-25-2015, 02:26 PM
  3. A Little Motec 101 M130 / M150
    By hotbird in forum 4-Tec Performance
    Replies: 16
    Last Post: 08-22-2014, 09:29 AM
  4. SOLD Motec m400 seadoo harness
    By shrabber in forum Sea Doo Classifieds
    Replies: 9
    Last Post: 03-17-2014, 10:34 PM
  5. DIY on Pump Upgrade
    By cvbwaller in forum Kawasaki How To & FAQs
    Replies: 0
    Last Post: 05-13-2013, 12:07 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •