Results 1 to 7 of 7
  1. #1
    98gsxl951's Avatar
    Join Date
    Jul 2008
    Location
    On my ski, on the CT river
    Posts
    879
    +1
    3

    looking for some riva thru hull installation tips and tricks before i start cutting .

    well pretty much got the old exhaust stuff out, minus the water box.

    I removed my opas a while back and added the extensions as awl as block offs.

    My questions as of now are what do i need to do to the stock IC bracket to get the exhaust pipe to clear the IC ?

    Also should i add some silicone to both the stock block off location as well as thru hull portion ?

    lastly the pipe has a hole in it at the end assuming its for the barb that was included, for the water outlet, but which water line am i disconnecting for this as the riva directions are VAGUE!

    any and all tips are appreciated and thanks in advance.


  2. #2
    Steve STSPERFORMANCE's Avatar
    Join Date
    Dec 2007
    Location
    Cambridge, Ohio
    Posts
    2,701
    +1
    116
    Here's a tip

    Throw out those bolts with nuts on the inside that hold the tip on

    Sheet metal screws and right stuff easy easy

  3. #3
    98gsxl951's Avatar
    Join Date
    Jul 2008
    Location
    On my ski, on the CT river
    Posts
    879
    +1
    3
    how bout the inter cooler bracket?

  4. #4
    98gsxl951's Avatar
    Join Date
    Jul 2008
    Location
    On my ski, on the CT river
    Posts
    879
    +1
    3
    also im just using the block off fitting at the end of the pipe and not the bard for a 09 rxpx correct? i didnt get any directions with this and am using this http://www.rivaracing.com/instructio...5050_1_255.pdf

  5. #5
    98gsxl951's Avatar
    Join Date
    Jul 2008
    Location
    On my ski, on the CT river
    Posts
    879
    +1
    3
    no input on this intercooler bracket aye?

  6. #6
    dirtywork255's Avatar
    Join Date
    Mar 2013
    Location
    hampton roads VA
    Posts
    14
    I just did one on my T-X you have to get the IC relocation kit. I also just blocked off the rear water fitting as there are no cooling lines that reach that far back. Plus there is a water line on the stock water box. I didnt use the rubber gasket for the exhaust outlet. Got some thru hull exhaust fitting sealent from west marine.

  7. #7
    98gsxl951's Avatar
    Join Date
    Jul 2008
    Location
    On my ski, on the CT river
    Posts
    879
    +1
    3
    ya im making my own right now, got the bracket roughed out, just need to mock the thing up and either make a new portion for the IC to rest on or use to oem upper portion.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. WTB - Parts looking for some riva seadoo nozzle rings
    By MILLER PHASE 3 1050 in forum Sea Doo Classifieds
    Replies: 0
    Last Post: 06-30-2013, 06:29 PM
  2. WTB WTB: riva thru hull exhaust tip
    By ryck80 in forum Sea Doo Classifieds
    Replies: 3
    Last Post: 07-06-2011, 04:18 PM
  3. Looking for a good thru hull exhaust for 04 RXP
    By HP Solutions in forum 4-Tec Performance
    Replies: 10
    Last Post: 06-22-2010, 09:35 PM
  4. Riva Thru Hull Exhaust Tip
    By Sea-Yaa in forum 4-Tec Performance
    Replies: 3
    Last Post: 12-28-2008, 01:51 PM
  5. GTX riva thru hull install
    By skoepp in forum 4-Tec Performance
    Replies: 5
    Last Post: 01-29-2008, 12:33 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •