Results 1 to 5 of 5
  1. #1
    I wanna go FAAAAASTer!! CDW78's Avatar
    Join Date
    Mar 2010
    Location
    Ky
    Posts
    543
    +1
    6

    Gpr 1200 Questions - several

    #1 - Looks like I need a new impeller duct stator whatever ( or are these repairable - where do I send it ? )
    Anyone got a good used one ?
    It seems to cavitate a little is why I tore it apart to begin with, assuming the prob / duct would be causing the issue ?

    #2 - How do you get the plate / wear ring housing etc off ? IT could be caulked with 42/5200 ( the pump shoe had the seal kit already )
    Do I need a new ring - can I use the plastic inserts in THIS housing ? I could see some light around the impeller, but not alot.

    #3 - Is the impeller any good or does that need to be replaced too ? ( notice the edges of it )

    #4 - IF I just make my own free flow exhaust - with pvc / some kinda metal / aluminum pipe take out the water box
    OR buy the hose that would keep the box ?

    #5 - Just getting an idea if it would work, but I've got the battery tray from the old gp1200 and as you see from the pics, would it be ok to relocate the battery there so I can use the under seat box for storage ?

    #6 - Is that shoe supposed to hang lower than the plate ?

    #7 - I want to relocate these pissers to the back under the grab handle / rail, have no idea why anyone would put them right there so they can fill the foot wells up - How do I seal the holes up correctly ?

    I know, a lot of questions, but figured I'd save it all for one post!
    THANKS

    Click image for larger version. 

Name:	20130604_160426.jpg 
Views:	64 
Size:	107.7 KB 
ID:	302806 Click image for larger version. 

Name:	20130604_160355.jpg 
Views:	59 
Size:	96.3 KB 
ID:	302807 Click image for larger version. 

Name:	20130604_160410.jpg 
Views:	55 
Size:	110.3 KB 
ID:	302808 Click image for larger version. 

Name:	20130604_160448.jpg 
Views:	61 
Size:	92.6 KB 
ID:	302809 Click image for larger version. 

Name:	20130604_160453.jpg 
Views:	58 
Size:	73.4 KB 
ID:	302810
    Last edited by CDW78; 06-04-2013 at 04:13 PM.


  2. #2
    I wanna go FAAAAASTer!! CDW78's Avatar
    Join Date
    Mar 2010
    Location
    Ky
    Posts
    543
    +1
    6
    Click image for larger version. 

Name:	20130604_160339.jpg 
Views:	63 
Size:	123.5 KB 
ID:	302811 Click image for larger version. 

Name:	20130604_155853.jpg 
Views:	51 
Size:	89.6 KB 
ID:	302812 Click image for larger version. 

Name:	20130604_125601.jpg 
Views:	51 
Size:	124.1 KB 
ID:	302813 Click image for larger version. 

Name:	20130604_145612.jpg 
Views:	46 
Size:	39.7 KB 
ID:	302814 Click image for larger version. 

Name:	20130604_145602.jpg 
Views:	58 
Size:	43.8 KB 
ID:	302815

  3. #3
    mudslanger's Avatar
    Join Date
    Jul 2010
    Location
    Huntsville Al
    Posts
    1,326
    +1
    49
    The wear ring will just pop off just take a pry bar and get behind it and give it a nudge. the stator needs replacing unless you can find someone to weld it up and grind it back down wright. the prop looks like its been hitting the wear ring and wile you got it down you can send that prop to Impros for repairs and trued. also replace the stator bearings and seals wile you got it down. the wear ring probably needs replaced also look close to where the stainless meets the aluminum and see if the stainless wear ring is separating from the aluminum if it is replace. if you go with the plastic you also have to buy the outer. they sell a all stainless wear ring. the pump shoe should sit a little below the ride plate. leave the water box and replace the plastic baffle with a aluminum 3 inch pipe may be 3.5 inch cant remember.

  4. #4
    I wanna go FAAAAASTer!! CDW78's Avatar
    Join Date
    Mar 2010
    Location
    Ky
    Posts
    543
    +1
    6
    WOW - almost 100 views and 1 answer!
    Thanks Mud!

  5. #5
    I wanna go FAAAAASTer!! CDW78's Avatar
    Join Date
    Mar 2010
    Location
    Ky
    Posts
    543
    +1
    6
    anyone have a stator/impeller duct to sale ?

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. gpr 1200 engine build questions
    By pjv911 in forum Yamaha PWC Performance (2-stroke)
    Replies: 4
    Last Post: 12-31-2011, 07:19 PM
  2. gpr 1200 carb questions
    By jeff12pv in forum Yamaha PWC Performance (2-stroke)
    Replies: 2
    Last Post: 02-03-2011, 09:17 AM
  3. Riva gas Power Valve Question 2001 gpr 1200
    By patrick webb in forum Yamaha PWC Performance (2-stroke)
    Replies: 4
    Last Post: 07-19-2009, 12:40 AM
  4. Question RE Dynafly on GPR 1200
    By Autosport in forum Yamaha PWC Performance (2-stroke)
    Replies: 15
    Last Post: 03-21-2008, 10:06 AM
  5. Need 2000 gpr 1200 opinions
    By shooter98xpl in forum Yamaha PWC Performance (2-stroke)
    Replies: 3
    Last Post: 12-05-2005, 08:53 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •