Results 1 to 5 of 5
  1. #1
    AWA MEMBER
    Join Date
    Jan 2008
    Location
    Currituck, North Carolina, United States
    Posts
    4,616
    +1
    247

    Anyone have a SC tool I can Borrow?

    I'm going to do a 09 clutch and Riva Dampner gear.......but I need the clutch holding tool......does anyone have one to let me borrow or sell me one?


  2. #2
    rick I just bought a custom one from a fellow forum member. It hasnt arrived yet should be here either today or Monday.
    He said is was laser cut and thinner than the R&D one. If you PROMISE to not screw me over and send it back immediately I will ship it to you when it arrives here. I would like it sent back USPS priority with tracking......I will send it the same since your in a bind and need to get back on the water.....Just cover shipping on my end.
    Should cost you 20bucks at most tp cover both ways. I just payed 60 for it sight unseen so hoping its a nice one:0)

  3. #3
    THE PLATE MAN JIM'S PERFORMANCE's Avatar
    Join Date
    Nov 2005
    Posts
    6,194
    +1
    536
    if you have an air compressor and a 3/8 impact wrench to fit in the front with a short 17 mm socket and make sure you have it turning right because it is left handed threads you do not need the tool.

  4. +1 by:


  5. #4
    yol937's Avatar
    Join Date
    Jul 2011
    Location
    Nc
    Posts
    1,071
    +1
    160
    Plus 1 Jim have done a few like this, works well

  6. #5
    AWA MEMBER
    Join Date
    Jan 2008
    Location
    Currituck, North Carolina, United States
    Posts
    4,616
    +1
    247
    Quote Originally Posted by scittb View Post
    rick I just bought a custom one from a fellow forum member. It hasnt arrived yet should be here either today or Monday.
    He said is was laser cut and thinner than the R&D one. If you PROMISE to not screw me over and send it back immediately I will ship it to you when it arrives here. I would like it sent back USPS priority with tracking......I will send it the same since your in a bind and need to get back on the water.....Just cover shipping on my end.
    Should cost you 20bucks at most tp cover both ways. I just payed 60 for it sight unseen so hoping its a nice one:0)


    might take ya up on that.....I'll let ya know I'm collecting parts now

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. ANYONE have, or know where I can find a 300X motor for sale?!?!
    By Javier in forum Kawasaki PWC Performance (4-stroke)
    Replies: 1
    Last Post: 02-12-2013, 08:49 PM
  2. Anyone have, or know where I can get RE Block off's?
    By geowelsh in forum 4-Tec Performance
    Replies: 6
    Last Post: 04-19-2011, 03:53 PM
  3. Anyone have rxp impeller tool?
    By Sturm215 in forum Sea Doo Open Discussion
    Replies: 1
    Last Post: 08-05-2010, 07:39 PM
  4. Anyone have a riva valvetrain tool I can borrow?? Need one asap
    By caliburst in forum 4-Tec Performance
    Replies: 4
    Last Post: 11-11-2009, 10:58 PM
  5. Anyone have an alignment tool?
    By rb26z32 in forum Polaris Open Discussion
    Replies: 8
    Last Post: 05-28-2008, 10:30 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •