Page 1 of 2 1 2 LastLast
Results 1 to 10 of 18
  1. #1

    Athena Idle Question

    Anyone know how to increase the idle using the Maya/Athena software? Any info would be appreciated


  2. #2
    Eric Ocman's Avatar
    Join Date
    Aug 2008
    Location
    Cataula, Georgia, United States
    Posts
    4,700
    +1
    77
    When you figure it out please share. Many people have issues with it. Low enough to make the oil pressure light come on at times and hard starting etc.
    Last edited by Ocman; 06-22-2013 at 10:40 AM.

  3. +1 by:


  4. #3
    Exactly, when you back off the throttle and go back to idle the oil light flashes and low oil psi shows on display, add a little throttle and it disappears?

  5. #4
    Sayers's Avatar
    Join Date
    Jul 2010
    Location
    Melbourne AUS
    Posts
    2,300
    +1
    134
    Do you have the latest firmware and map loaded?

  6. #5
    Yes, Rob and Bubba from Riva hooked me up

  7. #6
    speednutz's Avatar
    Join Date
    Feb 2013
    Location
    winona,mn
    Posts
    264
    +1
    8
    Mines idles at 1500-1700 rpms

  8. #7
    Sayers's Avatar
    Join Date
    Jul 2010
    Location
    Melbourne AUS
    Posts
    2,300
    +1
    134
    Quote Originally Posted by rxpx2012 View Post
    Yes, Rob and Bubba from Riva hooked me up
    And your still having idle drop issues causing oil press warning? Just get Rob or Bubba to adjust the map for you.

  9. #8
    SLASHER's Avatar
    Join Date
    Jun 2007
    Location
    Australia, Perth WA
    Posts
    3,263
    +1
    474
    I just don't get the ATHENA issues... Why isn't set right from factory like the old ECU. ...

    Hence why I went V TECH and happy with it ... I did want the ATHENA but not after seeing the issues ...

    Good luck ...

  10. +1 by:


  11. #9

    Athena Idle Issues

    To change the idle in Maya, I read you are supposed to change the target rpm under "Vector". Alright when you bring up Vector it shows cells from -24 to 201 with different rpms, I am guessing that these values are the engine temp and what target rpm corresponds to that temp. So how do you enter the target you need to stop the oil warning from flashing? and having a low rpm? My RXP-X always idled at 1700 dead nut with no fluctuations whatsoever with the stock ECU. There is a green positive sign and a red negative sign, is this where the change is made? If anyone has a clue please chime in, I would really enjoy riding the ski without the fear that something is wrong

  12. #10
    Water4fire's Avatar
    Join Date
    May 2005
    Location
    New Braunfels TX.
    Posts
    10,061
    +1
    790
    I wish I would have gotten the answer aswell. Get instructions on changeing the fuel table too. Because your gonna need it and if you get it. Please let everyone know.

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 2007 Speedster 200 High Idle Question
    By dgarza01 in forum 4-Tec Performance
    Replies: 32
    Last Post: 05-30-2012, 11:00 PM
  2. rr 8800 ecu for px idle question
    By Mike H in forum 4-Tec Performance
    Replies: 10
    Last Post: 11-13-2010, 06:57 AM
  3. slt 780 idle question?
    By dustin88 in forum Polaris Open Discussion
    Replies: 6
    Last Post: 08-29-2008, 09:48 AM
  4. Blaster Idle Question
    By DANGER1049 in forum Yamaha Old School Skis
    Replies: 2
    Last Post: 05-05-2008, 01:14 PM
  5. HELP - R12x Shuts Off and adjust Idle Question
    By tomasga in forum Honda How To & FAQs
    Replies: 5
    Last Post: 06-21-2007, 08:55 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •